Click here

VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1380

Click here
Click here Click here
DTC Code DTC Name
C1380 Stop Light Control Relay Malfunction
Click here

DESCRIPTION

Upon receiving the downhill assist control* or hill-start assist control operating signal from the skid control ECU (brake actuator assembly), the relay contact turns on and the stop light comes on.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1380 Stop Light Control Relay Malfunction

Either of the following is detected:


  1. When the voltage at the +BS terminal is 9.5 V or higher and the stop light control relay drive output (STPO) is on, a signal has not been input to the STP terminal for 2 seconds or more.

  2. When the voltage at the +BS terminal is 9.5 V or higher and the stop light control relay drive output (STPO) is off, the signal at the STP is different from the input signal at the STP2 for 2 seconds or more.

  • IG1 NO. 3 fuse

  • STOP fuse

  • Stop light switch circuit

  • Stop light control relay (STOP/CDS FAN Relay)

  • Stop light control relay circuit

  • Skid control ECU (Brake actuator assembly)
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • When replacing the skid control ECU (brake actuator assembly), perform calibration.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tip:

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first.

Click here

Click here

PROCEDURE


  1. Click here

    CHECK STOP LIGHT OPERATION


    1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

      OK
      Condition Illumination Condition
      Brake pedal depressed. On
      Brake pedal released. Off
      Result
      Result
      OK
      NG

  2. Click here

    CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Turn the ignition switch off.

    3. Disconnect the A4 skid control ECU (brake actuator assembly) connector.

    4. B0024ICC64
      *a

      Front view of wire harness connector

      (to Skid Control ECU [Brake Actuator Assembly])

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A4-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
      Stop light switch assembly off (Brake pedal released) Below 1.5 V
      Result
      Result
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

  3. Click here

    CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)


    1. B0024ICC65
      *a

      Front view of wire harness connector

      (to Skid Control ECU [Brake Actuator Assembly])

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A4-7 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
      Stop light switch assembly off (Brake pedal released) Below 1.5 V
      Result
      Result
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

  4. Click here

    PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)


    1. Reconnect the A4 skid control ECU (brake actuator assembly) connector.

    2. Connect the GTS to the DLC3.

    3. Start the engine.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


      1. Chassis > ABS/VSC/TRC > Active Test
        Tester Display Measurement Item Control Range Diagnostic Note
        Stop Light Relay Stop light control relay (STOP/CDS FAN Relay) Relay ON/OFF

        Stop lights come on

        Vehicle condition: Vehicle stopped


    6. While performing the Active Test, check the illumination condition of the stop lights and "Stop Light Relay Output" in the Data List.


      1. Chassis > ABS/VSC/TRC > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Stop Light Relay Output Stop light control relay (STOP/CDS FAN Relay) output ON or OFF

        OFF: Relay output off (Stop lights off)

        ON: Relay output on (Stop lights on)

        		 -



      1. Chassis > ABS/VSC/TRC > Active Test
        Active Test Display
        Stop Light Relay
        Data List Display
        Stop Light Relay Output





      Result
      Result Proceed to
      When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off A
      When Active Test performed, Data List item changes between ON and OFF, but stop lights do not turn on B

  5. Click here

    RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs.

      Click here


      1. Chassis > ABS/VSC/TRC > Clear DTCs


    3. Start the engine.

    4. Perform a road test.

    5. Check if the same DTC is output.

      Click here


      1. Chassis > ABS/VSC/TRC > Trouble Codes


      Result
      Proceed to
      DTC C1380 is not output
      DTC C1380 is output

    • DTC C1380 is not output

      USE SIMULATION METHOD TO CHECKClick here

    • DTC C1380 is output

      REPLACE BRAKE ACTUATOR ASSEMBLYClick here

  6. Click here

    INSPECT STOP LIGHT CONTROL RELAY (STOP/CDS FAN RELAY)


    1. Turn the ignition switch off.

    2. Remove the stop light control relay (STOP/CDS FAN Relay) from the engine room relay block and junction block.

    3. Inspect the stop light control relay (STOP/CDS FAN Relay).

      Click here

      OK
      The stop light control relay (STOP/CDS FAN Relay) is normal.
      Result
      Result
      OK
      NG

    • OKClick here
    • NG

      REPLACE STOP LIGHT CONTROL RELAY (STOP/CDS FAN RELAY)

  7. Click here

    CHECK TERMINAL VOLTAGE (STOP LIGHT POWER SOURCE TERMINAL)


    1. B002535C01
      *a

      Component without Stop Light Control Relay (STOP/CDS FAN Relay)

      (Engine Room Relay Block and Junction Block)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      5 - Body ground Always 11 to 14 V
      1 - Body ground Ignition switch ON 11 to 14 V
      Result
      Result
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. Click here

    CHECK HARNESS AND CONNECTOR (STPO TERMINAL)


    1. Install the stop light control relay (STOP/CDS FAN Relay).

    2. Make sure that there is no looseness in the locking part and connecting part of the connector.

    3. Disconnect the A4 skid control ECU (brake actuator assembly) connector.

    4. Turn the ignition switch to ON.

    5. B0024ICC66
      *a

      Front view of wire harness connector

      (to Skid Control ECU [Brake Actuator Assembly])

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A4-26 (STPO) - Body ground Ignition switch ON 11 to 14 V
      Result
      Result
      OK
      NG

    • OK

      REPLACE BRAKE ACTUATOR ASSEMBLYClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)