Click here

STEERING KNUCKLE(for 2WD) REMOVAL

Click here
Click here Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front axle hub removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Front wheel alignment adjustment

  • Clearing zero point calibration data

  • Yaw rate and acceleration sensor zero point calibration

 VSC malfunctioning

Click here
Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here

PROCEDURE


  1. Click here

    REMOVE FRONT WHEEL

    Click here

  2. Click here

    DISCONNECT FRONT SPEED SENSOR LH (w/ ABS)


    1. B0068CM

      Remove the bolt and harness clamp from the front absorber bracket.

    2. Remove the bolt and harness clamp from the front lower arm bracket.

    3. B0069A0

      Remove the bolt and harness clamp from the steering knuckle LH.

    4. Remove the bolt and front speed sensor LH.

      Note:

      Keep the sensor tip and sensor installation hole free from foreign matter.

  3. Click here

    DISCONNECT FRONT FLEXIBLE HOSE

    Click here

  4. Click here

    REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH

    Click here

  5. Click here

    REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH

    Click here

  6. Click here

    REMOVE FRONT DISC

    Click here

  7. Click here

    DISCONNECT TIE ROD END SUB-ASSEMBLY LH

    Click here

  8. Click here

    DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. B0068E2

      Remove the 2 bolts and disconnect the front lower No. 1 suspension arm assembly LH from the steering knuckle LH.

  9. Click here

    DISCONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH


    1. A01LEIG

      Support the front axle hub assembly with a jack.

    2. Remove the clip and nut.

    3. A01LAZFC01
      *a Turn
      *b Hold

      Using SST, disconnect the steering knuckle LH from the front upper suspension arm assembly LH.

      09628-62011
  10. Click here

    REMOVE KNUCKLE GREASE RETAINER CAP LH


    1. Secure the front axle hub sub-assembly LH between aluminum plates in a vise.

    2. A01LFZ2

      Using a screwdriver and hammer, tap out the knuckle grease retainer cap LH.

      Note:

      Be careful not to damage the steering knuckle LH.

  11. Click here

    REMOVE FRONT AXLE SHAFT NUT LH


    1. B0068K8

      Using a chisel and hammer, loosen the staked part of the front axle shaft nut LH.

      Note:

      • Completely loosen the staked part of the front axle shaft nut LH when removing it.

      • Do not damage the front axle hub sub-assembly LH.

    2. A01LD05

      Using a 36 mm socket wrench, remove the front axle shaft nut LH.

  12. Click here

    REMOVE FRONT SKID CONTROL ROTOR (w/ ABS)


    1. B0068NF

      Remove the front skid control rotor.

      Note:

      Take care not to scratch the serration of the front skid control rotor.

  13. Click here

    REMOVE FRONT INNER WHEEL BEARING SPACER LH (w/o ABS)


    1. B0068F7

      Remove the front inner wheel bearing spacer LH.

  14. Click here

    REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH


    1. A01L8YYC01
      *a Turn
      *b Hold

      Using SST, remove the 3 front axle hub bolts.

      09650-17011
    2. A01L8FXN01

      Install SST to the front axle hub assembly LH as shown in the illustration.

      09950-00020
    3. A01LET3N01

      Using SST and a press, remove the front axle hub assembly LH and front axle hub inner bearing (inner race) from the steering knuckle LH.

      09950-00020
      09950-60010 09951-00400

    4. Remove the 3 bolts and the dust cover.

  15. Click here

    REMOVE FRONT AXLE HUB HOLE SNAP RING LH


    1. B0069AF

      Using a snap ring pliers, remove the front axle hub hole snap ring from the steering knuckle LH.

  16. Click here

    REMOVE FRONT INNER AXLE HUB BEARING LH


    1. A01LB0MN01

      Using SST, remove the front inner axle hub bearing LH (outer side inner race) from the front axle hub sub-assembly LH.

      09950-40011 09951-04010 09952-04010 09953-04020 09954-04020 09955-04051 09957-04010 09958-04011
      09950-60010 09951-00250

    2. Remove the front inner axle hub bearing LH (inner side inner race) from the steering knuckle LH.

    3. A01LCRXN01

      Using SST and a hammer, tap out the front inner axle hub bearing LH (outer race) from the steering knuckle LH.

      09950-60020 09951-00710
      09950-70010 09951-07150
  17. Click here

    REMOVE FRONT AXLE HUB OIL SEAL LH


    1. Using a screwdriver, pry out the front axle hub oil seal LH from the front axle hub sub-assembly LH.