MANUAL TRANSMISSION ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

CAUTION:


  • B0068W8

    To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

  • B00281GC03
    *a Object Exceeding Weight Limit of Transmission Jack

    The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. Remove the shift lever knob sub-assembly from the shift lever.

  4. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

    Click here

  5. REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)

    Click here

  6. REMOVE SHIFT LEVER BOOT ASSEMBLY


    1. B00245Z

      Remove the 6 screws, 4 clips and shift lever boot assembly.

  7. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY


    1. B00294R

      Detach the shift lever cap boot from the manual transmission.

    2. Cover the shift lever cap with a cloth.

    3. B0026ANC02
      *1 Shift Lever Cap
      *a Press Down
      *b Counterclockwise
      *c Pull Out

      While pressing down on the shift lever cap, turn it counterclockwise, and then pull to remove the shift lever.

  8. REMOVE NO. 1 FLOOR SHIFT BUSH


    1. B0028TD

      Remove the No. 1 floor shift bush from the floor shift shift lever assembly.

  9. DRAIN MANUAL TRANSMISSION OIL

    Click here

  10. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

  11. REMOVE NO. 2 ENGINE UNDER COVER

  12. REMOVE PROPELLER SHAFT GUARD


    1. B0027WQ

      Remove the propeller shaft guard with the 2 bolts.

  13. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1GD-FTV)

    Click here

  14. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2GD-FTV)

    Click here

  15. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1KD-FTV)

    Click here

  16. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2KD-FTV)

    Click here

  17. REMOVE STARTER ASSEMBLY (for 1GD-FTV)


  18. REMOVE STARTER ASSEMBLY (for 2GD-FTV)


  19. REMOVE STARTER ASSEMBLY (for 1KD-FTV)


  20. REMOVE STARTER ASSEMBLY (for 2KD-FTV)


  21. REMOVE NO. 4 CYLINDER BROCK INSULATOR


    1. Remove the No. 4 cylinder block insulator.

  22. REMOVE STIFFENER PLATE LH


    1. B00268Y

      Remove the 4 bolts and stiffener plate LH.

  23. REMOVE STIFFENER PLATE RH


    1. B0027BI

      Remove the 4 bolts and stiffener plate RH.

  24. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY


  25. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

    Click here

  26. DISCONNECT GROUND CABLE


    1. B0027G6

      Remove the bolt and disconnect the ground cable.

  27. SUPPORT MANUAL TRANSMISSION ASSEMBLY


    1. B0025E7

      Support the manual transmission with a transmission jack.

      Note


      • Make sure the high transmission jack attachment is centered on the safety stand.

      • Secure the part with a rope, attachment, etc.

  28. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    1. B0027MH

      Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.

    2. B0024SA

      Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.

  29. REMOVE REAR ENGINE MOUNTING INSULATOR


    1. B002713

      Remove the 4 bolts and rear engine mounting insulator from the manual transmission assembly.

  30. DISCONNECT WIRE HARNESS


    1. B002950

      w/ Intelligent Manual Transmission Switch:


      1. Detach the 7 wire harness clamps.

      2. Remove the bolt.

      3. Disconnect the 3 connectors and wire harness.

    2. B0024UF

      w/o Intelligent Manual Transmission Switch:


      1. Detach the 5 wire harness clamps.

      2. Remove the bolt.

      3. Disconnect the 2 connectors and wire harness.

  31. REMOVE MANUAL TRANSMISSION ASSEMBLY


    1. B0027CS

      Remove the 5 bolts and manual transmission assembly.

      Note

      As the manual transmission assembly is very heavy, be sure to support it securely.

  32. REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY


    1. B0026AS

      Detach the 4 breather hose clamps and bracket.

    2. Remove the transmission breather sub-assembly from the control shift lever retainer assembly.

    3. B0024YY

      Remove the 2 bolts and 2 brackets.

  33. REMOVE WIRING HARNESS CLAMP BRACKET


    1. B002883

      w/ Intelligent Manual Transmission Switch:


      1. Remove the 8 bolts and 7 wiring harness clamp brackets.

    2. B002575

      w/o Intelligent Manual Transmission Switch:


      1. Remove the 7 bolts and 6 wiring harness clamp brackets.

  34. REMOVE TRANSFER ASSEMBLY

    Click here