MANUAL TRANSMISSION ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.

PROCEDURE


  1. INSTALL TRANSFER ASSEMBLY

    Click here

  2. INSTALL WIRE HARNESS CLAMP BRACKET


    1. B00262Y

      Install the wire harness clamp bracket to the manual transmission unit assembly with the bolt.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  3. INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY


    1. A01SK2L

      Connect the 3 clamps and install the transmission breather sub-assembly.

  4. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

    CAUTION:

    The manual transmission unit assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


    1. Make sure that the knock pins are not loose, bent, damaged or scratched.

    2. Operate the transmission jack and install the manual transmission unit assembly to the vehicle.

      CAUTION:

      Do not raise the manual transmission unit assembly more than necessary. If the manual transmission unit assembly is raised excessively, the vehicle may also be lifted up.

      Note

      Make sure that the manual transmission unit assembly is clear of all wiring and hoses.

    3. Align the input shaft with the clutch disc and install the manual transmission unit assembly to the engine.

    4. B002811C01
      *1 Transmission Breather Bracket

      Install the transmission breather bracket and 7 bolts.

      Torque:
      for bolt A
      71.5 N*m  { 729 kgf*cm, 53 ft.*lbf }
      for bolt B
      37.2 N*m  { 379 kgf*cm, 27 ft.*lbf }

  5. INSTALL REAR ENGINE MOUNTING INSULATOR


    1. Install the rear engine mounting insulator with the 4 bolts.

      Torque:
      47 N*m  { 479 kgf*cm, 35 ft.*lbf }

  6. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    1. Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

      Torque:
      57 N*m  { 581 kgf*cm, 42 ft.*lbf }

    2. Connect the No. 3 frame crossmember sub-assembly to the rear engine mounting insulator.

      Torque:
      18.5 N*m  { 189 kgf*cm, 14 ft.*lbf }

  7. INSTALL STARTER ASSEMBLY


    1. for 2.0 kW Type:

      Click here

    2. except 2.0 kW Type:

      Click here

  8. CONNECT GROUND CABLE


    1. B0027EE

      Connect the ground cable with the bolt.

      Torque:
      19.5 N*m  { 199 kgf*cm, 14 ft.*lbf }

  9. CONNECT WIRE HARNESS


    1. A01SHBG

      Connect the 6 clamps and 2 connector.

  10. INSTALL MANIFOLD STAY

    Click here

  11. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  12. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

    Click here

  13. INSTALL FRONT PROPELLER SHAFT ASSEMBLY

    Click here

  14. INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY

    Click here

  15. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  16. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here

  17. ADD MANUAL TRANSMISSION OIL

    Click here

  18. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY


    1. B00246BC01
      B0068HS MP grease

      Apply MP grease to the tip of the shift lever.

    2. B0025SXC01
      *a Press down
      *b Clockwise
      *c Lock

      Cover the shift lever cap with a cloth.

    3. While pressing down on the shift lever cap, turn it clockwise to install the shift lever.

    4. Attach the shift lever cap boot.

  19. INSTALL SHIFT LEVER BOOT ASSEMBLY


    1. Install the shift lever boot assembly with the 6 screws and 4 clips.

  20. INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

    Click here

  21. INSTALL FRONT CONSOLE BOX (w/o Console Box Lid)

    Click here

  22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here