Click here

AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV), Diagnostic DTC:P2714

Click here
Click here Click here
DTC Code DTC Name
P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)
Click here

SYSTEM DESCRIPTION

The shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) The ECM detects a malfunction in the shift solenoid valve SLT (ON side) according to the difference in the speed between the turbine and the output shaft, and also by the ATF pressure. (2 trip detection logic)
  • Shift solenoid valve SLT remains open

  • Shift solenoid valve SL1, SL2, SL3 or SL4 remains open or closed

  • Transmission valve body assembly is blocked

  • Automatic transmission assembly (clutch, brake or gear, etc.)

Comes on DTC stored
Click here

MONITOR DESCRIPTION

The ECM calculates the amount of clutch slip based on the input turbine speed, output shaft speed, and gear ratio. If the amount of clutch slip exceeds a specified level, the ECM will set this DTC and illuminate the MIL.

When shift solenoid valve SLT remains on, the line pressure goes down and clutch engagement force decreases.

Note:

If the vehicle continues to be driven under these conditions, the clutch will burn up and the vehicle will no longer be drivable.

Click here

CAUTION / NOTICE / HINT

Note:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click here

Tip:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Perform the D Position Shift Test in Road Test.*1

    Click here

  2. Turn the ignition switch off.

  3. Perform step (*1) again.

  4. Check for DTCs again.

    Click here

Click here

PROCEDURE


  1. Click here

    CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


      1. Powertrain > Engine > Trouble Codes


    5. Read the DTCs using the GTS.

      Result
      Result Proceed to
      Only DTC P2714 is output A
      P2714 and other DTCs are output B
      Tip:

      If a solenoid is stuck on, DTCs for several solenoids including the malfunctioning solenoid will be detected.


  2. Click here

    PERFORM ACTIVE TEST USING GTS (ACTIVATE THE SOLENOID (SLT))

    Note:
    • Perform the test while the ATF (Automatic Transmission Fluid) temperature is between 50 and 80°C (122 and 176°F).

    • Be careful to prevent the hose of SST from interfering with the exhaust pipe.

    • This check must be conducted after checking and adjusting the engine.

    • Perform the test with the air conditioning off.

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Turn the ignition switch off.

    2. Lift the vehicle up.

    3. B0024XFE01

      Remove the test plug from the transmission case and connect SST.

      09993-19015 09993-00010 09993-00040
    4. Lower the vehicle.

    5. Fully apply the parking brake and chock the 4 wheels.

    6. Connect the GTS to the DLC3.

    7. Start the engine.

    8. Warm up the ATF (Automatic Transmission Fluid).

    9. Measure the line pressure when the engine is idling.

    10. Turn the GTS on.

    11. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    12. Follow the instructions on the GTS and perform the Active Test.

    13. Measure the line pressure with SST.


      1. Powertrain > Engine > Active Test
        Tester Display Measurement Item Control Range Diagnostic Note
        Activate the Solenoid (SLT) Operates shift solenoid valve SLT to raise the line pressure.

        ON/OFF

        Tip:

        ON: No action (normal operation)

        OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the shift solenoid valve SLT to turn off).

        [Vehicle Condition]


        • Vehicle stopped

        • Engine idling




      1. Powertrain > Engine > Active Test
        Tester Display
        Activate the Solenoid (SLT)





      • The "Activate the Solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test.

        Click here

      Tip:

      Note that the pressure readings for the Active Test and Hydraulic Test are different.

      OK
      The line pressure changes as specified when performing the Active Test.
      Result
      Proceed to
      OK
      NG

  3. Click here

    PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION)

    Note:

    This test should always be performed with at least 2 people.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    7. According to the display on the GTS, perform the Active Test.

      Tip:

      Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.

      Click here


      1. Powertrain > Engine > Active Test
        Tester Display Measurement Item Control Range Diagnostic Note
        Control the Shift Position Operates the shift solenoid valves to allow gears to be selected manually.
        • Press "→" button: Up-shift occurs

        • Press "←" button: Down-shift occurs

        Can be used to check the operation of the shift solenoid valves.

        Up-shifts and down-shifts should be performed consecutively. A 10 second interval is required between gear changes.

        Do not down-shift at high speeds.

        Doing so will damage the automatic transmission.


        • [Vehicle Condition]
        • 50 km/h (31 mph) or less




      1. Powertrain > Engine > Active Test
        Tester Display
        Control the Shift Position




      Tip:
      • This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.

      • The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.

      • The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.

      • Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

      • The gear commanded by the ECM is shown in the Data List / Shift Status display on the GTS.

    8. Compare the ECM commanded gear and the actual gear.

      Result
      Actual Gear during Malfunction ECM Commanded Gear Proceed to
      1st 2nd 3rd 4th 5th 6th
      Shift solenoid valve SL1 Stuck ON 1st 2nd 3rd 4th 4th 4th A
      Stuck OFF N*1 N*1 N*1 N*1 5th 6th
      Shift solenoid valve SL2 Stuck ON 4th 4th 4th 4th 5th 6th B
      Stuck OFF 1st 2nd 3rd 1st N*1 N*1
      Shift solenoid valve SL3 Stuck ON 2nd 2nd 3rd 4th 5th 6th C
      Stuck OFF 1st 1st 3rd 4th 5th N*1
      Shift solenoid valve SL4 Stuck ON 3rd 3rd 3rd 4th 5th 5th D
      Stuck OFF 1st 2nd 1st 4th N*1 6th
      Shift solenoid valve SLT Stuck ON N*2 N*2 N*2 N*2 N*2 N*2 E
      Stuck OFF*3 1st 2nd 3rd 4th 5th 6th
      Tip:
      • *1: Neutral

      • *2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.

      • *3: When shift solenoid valve SLT is stuck off, gear shifting is normal.


    • A

      GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE SL1 PERFORMANCE DTC P0746)Click here

    • B

      GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE SL2 PERFORMANCE DTC P0776)Click here

    • C

      GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE SL3 PERFORMANCE DTC P0796)Click here

    • D

      GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE SL4 PERFORMANCE DTC P2808)Click here

    • EClick here
  4. Click here

    INSPECT SHIFT SOLENOID VALVE SLT


    1. B0025VIC15
      *1 Shift Solenoid Valve SLT

      Remove shift solenoid valve SLT.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
    3. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      Table 1. OK
      Measurement Condition Specified Condition

      • Battery positive (+) with a 21 W bulb → Terminal 1

      • Battery negative (-) → Terminal 2

      Valve moves and makes an operating noise.
      Result
      Proceed to
      OK
      NG

  5. Click here

    INSPECT TRANSMISSION VALVE BODY ASSEMBLY


    1. Check the transmission valve body assembly.

      Click here

      OK
      There is no foreign matter on each valve and they operate smoothly.
      Result
      Proceed to
      OK
      NG

    • OK

      REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLYClick here

    • NG

      REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLYClick here