TRANSMISSION CONTROL CABLE INSTALLATION

PROCEDURE


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    2. Connect the transmission control cable assembly to the vehicle body with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    3. B006LOZC01
      *a P
      *b N

      Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches to N.

    4. Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    5. Install a new clip to the No. 1 transmission control cable bracket.

    6. Turn the nut approximately 180° counterclockwise. While holding the nut in place, push in the stopper until it clicks twice.

      B006QNFC01
      *a Nut *b Turn approximately 180°
      *c Stopper *d Push in

      Note

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

    7. Connect the transmission control cable assembly to the shift lever assembly. Check that the spring is positioned at (A) and push in the stopper.

      B006NRWC01
      *1 Shift Lock Control Unit Assembly - -
      *a Spring *b Push in
      *c Stopper *d Nut

      Note


      • If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

      • Make sure that the transmission control cable assembly is securely locked.

    8. B006QFIC01
      *a Pin

      Connect the transmission control cable assembly to the shift lever assembly.

      Note


      • The shift lever should be in N.

      • Connect the transmission control cable assembly all the way to the base of the pin.

  2. INSTALL NO. 1 DASH PANEL HEAT INSULATOR


    1. Install the No. 1 dash panel heat insulator to the vehicle body with the 3 nuts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  3. INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

    Click here

  4. CONNECT HEATED OXYGEN SENSOR CONNECTOR (for Bank 1)

    Click here

  5. INSTALL CONSOLE BOX ASSEMBLY (for Integrated Type)

    Click here

  6. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Separate Console Box Type)

    Click here

  7. INSTALL INSTRUMENT PANEL BOX ASSEMBLY (for Separate Console Box Type)

    Click here

  8. INSTALL CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL (for Separate Console Box Type)

    Click here

  9. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL (for Separate Console Box Type)

    Click here

  10. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  11. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

    Click here

  12. INSTALL BATTERY

    Click here

  13. INSTALL V-BANK COVER SUB-ASSEMBLY

    Click here

  14. INSTALL CENTER NO. 1 COWL TOP VENTILATOR LOUVER

    Click here

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  16. INSPECT SHIFT LEVER POSITION

    Click here

  17. ADJUST SHIFT LEVER POSITION

    Click here

  18. INSPECT FOR EXHAUST GAS LEAK