SPIRAL CABLE INSTALLATION

PROCEDURE


  1. INSPECT SPIRAL CABLE SUB-ASSEMBLY WITH SENSOR


    1. B005B9QC01
      *a Check Window
      *b Matchmark
      *c Top of Flat Cable U-turn

      Check that the spiral cable sub-assembly with sensor is center position.

      OK
      The connector is at the top.
      The matchmarks are aligned.
      The top of the flat cable U-turn can be checked from the check window.

    2. If the spiral cable sub-assembly with sensor is not centered, center it.

      Note

      Failure to observe the following precautions may result in damage to the spiral cable sub-assembly with sensor.


      • When rotating the spiral cable sub-assembly with sensor, make sure to push on the interlock to release the interlock.

      • Do not turn the spiral cable sub-assembly with sensor using the airbag wire harness.

      • Do not forcibly rotate the part.


      1. B0057LJC01
        B0059LJ Interlock
        B0057RX Counterclockwise

        While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable sub-assembly with sensor counterclockwise slowly by hand until it stops.

        Note

        Make sure to rotate the spiral cable sub-assembly with sensor counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.

        Tech Tips

        The interlock operates at the top and bottom of the connector.

      2. B0058K2

        If the spiral cable sub-assembly with sensor stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.

      3. B005B7MC01
        B0059LJ Interlock
        B0057RX Clockwise

        While pushing on the interlock, rotate the spiral cable sub-assembly with sensor clockwise approximately 2.5 times to move the connector from the bottom to the top.

        Note

        If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly with sensor may be damaged.

        Tech Tips

        The interlock operates at the top and bottom of the connector.

      4. B005B9QC01
        *a Check Window
        *b Matchmark
        *c Top of Flat Cable U-turn

        Check that the spiral cable sub-assembly with sensor is center position.

        OK
        The connector is at the top.
        The matchmarks are aligned.
        The top of the flat cable U-turn can be checked from the check window.

        Note

        If the spiral cable sub-assembly with sensor cannot be centered, it is possible that the spiral cable sub-assembly with sensor is broken. Replace the spiral cable sub-assembly with sensor with a new one.

  2. INSTALL SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral with sensor cable sub-assembly with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral with sensor cable sub-assembly with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the front wheels are facing straight ahead.

    4. Set the turn signal switch to the neutral position.

      Note

      If it is not in the neutral position, the turn signal switch cancel ratchet may snap.

    5. Attach the 3 claws to install the spiral with sensor cable sub-assembly.

      Note

      When replacing the spiral with sensor cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

    6. Connect each connector.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    7. B0057X1C05
      *a Slider
      *b Lock Position

      Connect the airbag connector and check that the slider is in the lock position.

      Tech Tips

      If the slider is not in the lock position, the airbag connector is not completely connected. Disconnect the airbag connector, check the airbag connector and spiral with sensor cable sub-assembly terminals and connector housings for deformation or foreign matter, and then reconnect the airbag connector.

  3. INSTALL UPPER STEERING COLUMN COVER

    for Manual Tilt and Manual Telescopic Steering Column:

    Click here

    for Power Tilt and Power Telescopic Steering Column:

    Click here

  4. INSTALL LOWER STEERING COLUMN COVER

    for Manual Tilt and Manual Telescopic Steering Column:

    Click here

    for Power Tilt and Power Telescopic Steering Column:

    Click here

  5. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  6. ADJUST SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. B0058RQC01
      *a Check Window
      *b Top of Flat Cable U-turn

      Check that the spiral cable sub-assembly with sensor is center position.

      OK
      The connector is at the top.
      The top of the flat cable U-turn can be checked from the check window.

    4. If the spiral cable sub-assembly with sensor is not centered, center it.

      Note

      Failure to observe the following precautions may result in damage to the spiral cable sub-assembly with sensor.


      • When rotating the spiral cable sub-assembly, make sure to push on the interlock to release the interlock.

      • Do not turn the spiral cable sub-assembly with sensor using the airbag wire harness.

      • Do not forcibly rotate the part.


      1. B00579PC01
        B0059LJ Interlock
        B0057RX Counterclockwise

        While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable sub-assembly with sensor counterclockwise slowly by hand until it stops.

        Note

        Make sure to rotate the spiral cable sub-assembly with sensor counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.

        Tech Tips

        The interlock operates at the top and bottom of the connector.

      2. B005A0P

        If the spiral cable sub-assembly with sensor stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.

      3. B0058QXC01
        B0059LJ Interlock
        B0057RX Clockwise

        While pushing on the interlock, rotate the spiral cable sub-assembly with sensor clockwise approximately 2.5 times to move the connector from the bottom to the top.

        Note

        If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly with sensor may be damaged.

        Tech Tips

        The interlock operates at the top and bottom of the connector.

      4. B0058RQC01
        *a Check Window
        *b Top of Flat Cable U-turn

        Check that the spiral cable sub-assembly with sensor is center position.

        OK
        The connector is at the top.
        The top of the flat cable U-turn can be checked from the check window.

        Note

        If the spiral cable sub-assembly with sensor cannot be centered, it is possible that the spiral cable sub-assembly with sensor is broken. Replace the spiral cable sub-assembly with sensor with a new one.

  7. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  9. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  10. CHECK SRS WARNING LIGHT

    Click here