FRONT SUSPENSION MEMBER REMOVAL

PROCEDURE


  1. FRONT WHEELS FACING STRAIGHT AHEAD

  2. SECURE STEERING WHEEL

    Click here

  3. REMOVE COLUMN HOLE COVER SILENCER SHEET

    Click here

  4. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

    Click here

  5. REMOVE FRONT WHEELS

    Click here

  6. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here

  7. REMOVE REAR ENGINE UNDER COVER RH

    Click here

  8. REMOVE REAR ENGINE UNDER COVER LH

    Click here

  9. REMOVE FRONT CENTER FLOOR COVER LH

    Click here

  10. REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH


    1. A01HGIL

      Remove the 4 bolts and front suspension member reinforcement LH.

  11. REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH


    1. A01HG3Y

      Remove the 4 bolts and front suspension member reinforcement RH.

  12. REMOVE FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT (for 3ZR-FAE 2WD)


    1. B0057DB

      Remove the 2 bolts and front lower engine mounting bracket reinforcement.

  13. DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH


    1. A01HFOH

      Remove the nut and disconnect the front stabilizer link assembly LH from the front stabilizer bar.

      Tech Tips

      If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.

  14. DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. DISCONNECT TIE ROD END SUB-ASSEMBLY LH

    Click here

  16. DISCONNECT TIE ROD END SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

    Click here

  18. DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH

    A01HHX0

    1. Remove the 3 bolts and front suspension member rear brace LH.

  20. REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    1. A01HG5R

      Remove the 2 bolts and 2 nuts, and disconnect the front suspension crossmember sub-assembly from the rear engine mounting insulator.

    2. A01HJ8ZC02
      *a Engine Lifter
      *b Attachment
      B0057KY Attachment placement location

      Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

      Note


      • Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

      • Use the attachments to keep the front suspension crossmember sub-assembly level.

      • The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.

    3. A01HFDU

      Remove the 2 bolts and front suspension crossmember sub-assembly.

    4. Slowly lower the front suspension crossmember sub-assembly.

      Note

      When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.

  22. REMOVE FRONT CROSSMEMBER SUB-ASSEMBLY


    1. A01HFAW

      Using a jack, support the engine and transaxle assembly.

    2. A01HG8A

      Remove the 6 bolts and front crossmember sub-assembly.

  23. REMOVE STEERING GEAR ASSEMBLY

    Click here

  24. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    1. A01HFBDC02
      B0057RX Bolt
      B0059IK Nut

      Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.

      Note

      Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.

  25. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. REMOVE FRONT SUSPENSION MEMBER BRACE

    Click here

  27. REMOVE FRONT STABILIZER BAR


    1. A01HF0L

      Remove the front stabilizer bar with the 2 front stabilizer bar bushings from the front suspension crossmember sub-assembly.