AUDIO AND VISUAL SYSTEM(for 10.3 Inch Display), Diagnostic DTC:B153B

DTC Code DTC Name
B153B DAB (Digital Audio Broadcasting) Antenna 2 Disconnected

DESCRIPTION

This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna (sub) which is connected to the radio receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B153B DAB (Digital Audio Broadcasting) Antenna 2 Disconnected The digital audio broadcasting antenna (sub) is not connected

  • No. 1 antenna cord sub-assembly

  • No. 2 antenna cord sub-assembly

  • No. 3 antenna cord sub-assembly

  • Digital audio broadcasting antenna assembly LH

  • Window shield glass (window glass antenna wire)

  • Radio receiver assembly

WIRING DIAGRAM

B002IHOE01

CAUTION / NOTICE / HINT

Note

When replacing the radio receiver assembly, always replace it with a new one.

If a radio receiver assembly which was installed to another vehicle is used, the following may occur:


  • A communication malfunction DTC may be stored.

  • The radio receiver assembly may not operate normally.

Tech Tips

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here

PROCEDURE


  1. CHECK CONNECTION OF DIGITAL AUDIO BROADCASTING ANTENNA CABLE


    1. Check if the digital audio broadcasting antenna cable is securely connected to the radio receiver assembly.

      OK
      Digital audio broadcasting antenna cable is securely connected
      Result
      Proceed to
      OK
      NG

    NG

    SECURELY CONNECT DAB RADIO ANTENNA CABLE

    OK

  2. CHECK WINDOW SHIELD GLASS (WINDOW GLASS ANTENNA WIRE)


    1. B002KK2C29
      *a Tester Probe
      *b Antenna Wire
      *c Tin Foil

      Check for continuity in the window glass antenna wire.

      Tech Tips

      Check for continuity at the center of each antenna wire as shown in the illustration.

      Note

      When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.

      OK
      There is continuity in the window glass antenna wire.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR WINDOW SHIELD GLASS (WINDOW GLASS ANTENNA WIRE)

    OK

  3. CHECK NO. 1 ANTENNA CORD SUB-ASSEMBLY


    1. B002JRAC01
      *a

      Front view of wire harness connector

      (to Radio Receiver Assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)

      Disconnect the antenna connector from the radio receiver assembly.

    2. Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      DB-2 (DAB-LH [SUB]) - C-1 Always Below 1 Ω
      DB-2a - C-1a Always Below 1 Ω
      DB-2 (DAB-LH [SUB]) - Body ground Always 10 kΩ or higher
      DB-2a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 1 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  4. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. B002HJIC01
      *a

      Front view of wire harness connector

      (to No. 1 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to No. 3 Antenna Cord Sub-assembly)

      Disconnect the antenna connector from the No. 1 antenna cord sub-assembly.

    2. Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C-1 - B-3 Always Below 1 Ω
      C-1a - B-3a Always Below 1 Ω
      C-1 - Body ground Always 10 kΩ or higher
      C-1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  5. CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. B002H5CC01
      *a

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to Digital Audio Broadcasting Antenna Assembly LH)

      Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.

    2. Disconnect the antenna connector from the digital audio broadcasting antenna assembly LH

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B-3 - A-1 Always Below 1 Ω
      B-3a - A-1a Always Below 1 Ω
      B-3 - Body ground Always 10 kΩ or higher
      B-3a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  6. CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH


    1. Replace the digital audio broadcasting antenna assembly LH with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here