АВТОМАТИЧЕСКАЯ ТРАНСМИССИЯ В СБОРЕ (если опорный мост двигателя не используется) УСТАНОВКА

PROCEDURE


  1. INSTALL TORQUE CONVERTER ASSEMBLY


    1. A002CC3C01
      *a Matchmark
      *b Key

      Turn the front oil pump drive gear so that either key is at the top and place a matchmark on the transaxle housing to indicate the position of the key.

    2. A002BV6C01
      *a Groove
      *b Matchmark
      B003ZIE MP Grease

      Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.

    3. A0028Z4C02
      *1 Front Oil Pump Oil Seal
      *a Matchmark

      Align the matchmark on the torque converter assembly with the one on the transaxle housing and engage the splines of the input shaft with the turbine runner splines.

      Note


      • Install the torque converter assembly to the input shaft while keeping it horizontal.

      • Do not damage the front oil pump oil seal.

    4. A002BVYC02
      *1 Front Oil Pump Oil Seal
      *a Matchmark

      Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

      Note


      • Do not push the torque converter assembly excessively when rotating it.

      • Install the torque converter assembly to the input shaft while keeping it horizontal.

      • Do not damage the front oil pump oil seal.

    5. A002BNFC01
      *1 Front Oil Pump Oil Seal
      *a Matchmark

      Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the keys of the front oil pump drive gear into the grooves of the torque converter assembly.

      Note


      • Do not push the torque converter assembly excessively when rotating it.

      • Install the torque converter assembly to the input shaft while keeping it horizontal.

      • Do not damage the front oil pump oil seal.

    6. Clean the drive plate and torque converter assembly setting bolt holes.

    7. A0028JRC01
      *a Engine Assembly Surface
      *b Drive Plate and Ring Gear Sub-assembly Surface

      Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surface of the drive plate and ring gear sub-assembly*b.

      Note

      Make sure to deduct the thickness of the straightedge.

    8. A0027OJC01

      Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

      Standard
      Dimension (A) + 1 mm (0.0394 in.) or more

      Note


      • Make sure to deduct the thickness of the straightedge.

      • If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

      • Do not include the thickness of the set block.

  2. INSTALL BREATHER PLUG HOSE


    1. Install the breather plug sub-assembly to the breather plug hose.

    2. Install the breather plug hose to the No. 1 breather plug (ATM).

  3. INSTALL TRANSMISSION CASE PLUG ASSEMBLY


    1. Coat the O-ring of a new transmission case plug assembly with Toyota Genuine ATF WS.

    2. Install the transmission case plug assembly to the automatic transaxle assembly.

  4. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  5. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. Install the No. 1 transmission control cable bracket to the automatic transaxle case sub-assembly with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  6. INSTALL FRONT ENGINE MOUNTING BRACKET


    1. Install the front engine engine mounting bracket to the automatic transaxle assembly with the 4 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  7. INSTALL ENGINE MOUNTING BRACKET LH


    1. Install the engine engine mounting bracket LH to the automatic transaxle assembly with the 3 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  8. INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

    Click here

  9. CONNECT OUTLET NO. 1 OIL COOLER HOSE

    Click here

  10. INSTALL TRANSMISSION OIL COOLER

    Click here

  11. CONNECT OUTLET NO. 3 OIL COOLER HOSE

    Click here

  12. CONNECT INLET NO. 2 OIL COOLER HOSE

    Click here

  13. CONNECT NO. 3 WATER BY-PASS HOSE

    Click here

  14. CONNECT NO. 4 WATER BY-PASS HOSE

    Click here

  15. INSTALL RADIATOR PIPE ASSEMBLY


    1. Install the radiator pipe assembly to the automatic transaxle assembly with the bolt.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

    2. Install the No. 3 water by-pass hose and the No. 4 water by-pass hose to the radiator pipe assembly and slide the 2 clips to secure them.

      A002CLKC03
      *1 Radiator Pipe Assembly *2 No. 3 Water By-pass Hose
      *3 No. 4 Water By-pass Hose - -
      *a 2 to 7 mm (0.0787 to 0.276 in.) *b Paint Mark
      *c 45° (Claw of Clip Location) - -

      Note


      • Make sure to slide the No. 3 water by-pass hose and the No. 4 water by-pass hose until each contacts the hose stopper of the radiator pipe assembly.

      • Make sure to align the paint mark of each hose with the paint mark of each tube.

  16. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY


    1. A002A24C01
      *1 Crankshaft
      *2 Torque Converter Assembly Centerpiece
      B003ZIE Clutch Spline Grease

      Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

      Clutch Spline Grease
      Toyota Genuine Clutch Spline Grease or equivalent
      Maximum Grease Amount
      Approximately 1 g (0.0353 oz)
    2. A002ARYC01
      *1 Knock Pin

      Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.

    3. A0029R3N01

      While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 11 bolts shown in the illustration.

      Torque:
      Bolt (A)
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }
      Bolt (B)
      46 N*m  { 469 kgf*cm, 34 ft.*lbf }
      Bolt (C)
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }
      Bolt Length
      Bolt Length
      (A) 55 mm (2.17 in.)
      (B) 41 mm (1.61 in.)
      (C) 33 mm (1.30 in.)

      Note


      • Confirm that the knock pins are installed to the automatic transaxle assembly contact surface of the cylinder block sub-assembly before installing the automatic transaxle assembly.

      • Do not forcibly pry on the automatic transaxle assembly.

      • Check that the torque converter assembly rotates.

  17. INSTALL MANIFOLD STAY


    1. A00280QC05
      B003ZIE Bolt
      A002B7OC11 Nut

      Install the bolt and nut in the order shown in the illustration.

      Torque:
      Bolt
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }
      Nut
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  18. INSTALL FRONT FRAME ASSEMBLY

    Click here

  19. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

    Click here

  20. INSTALL BREATHER PLUG HOSE


    1. Engage the 3 hose clamps to install the breather plug hose.

  21. CONNECT ENGINE WIRE


    1. A002B5VC01
      *a Transmission Wire Connector
      *b Park/Neutral Position Switch Assembly Connector
      B003ZIE Bolt
      B003Z8F Nut

      Connect the engine wire to the automatic transaxle case sub-assembly with the 2 bolts and nut.

      Torque:
      Bolt (A)
      25.5 N*m  { 260 kgf*cm, 19 ft.*lbf }
      Bolt (B)
      19.1 N*m  { 195 kgf*cm, 14 ft.*lbf }
      Nut
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

    2. Connect the park/neutral position switch connector.

    3. Connect the connector of the transmission wire connector and rotate the lever to engage the claw.

      Tech Tips

      Rotate the lever until the claw of the transmission wire connector makes a click sound.

  22. INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT


    1. Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.

    2. B003ZF3C22
      *a Adhesive

      Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

      Note

      Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.

    3. Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

      Torque:
      41 N*m  { 418 kgf*cm, 30 ft.*lbf }

      Note

      First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.

  23. INSTALL FLYWHEEL HOUSING UNDER COVER

    Click here

  24. CHECK AUTOMATIC TRANSAXLE SYSTEM

    Note

    If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

    Click here