DIFFERENTIAL OIL SEAL REPLACEMENT

PROCEDURE


  1. REMOVE NO. 1 ENGINE UNDER COVER

    Click here

  2. REMOVE FRONT FENDER APRON SEAL LH

    Click here

  3. DRAIN AUTOMATIC TRANSAXLE FLUID


    1. A002BQ2

      Remove the refill plug and gasket from the automatic transaxle case sub-assembly.

    2. A00276D

      Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.

    3. A002CA8C01
      *1 No. 1 Transmission Oil Filler Tube

      Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.

    4. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

      Torque:
      1.7 N*m  { 17 kgf*cm, 15 in.*lbf }

    5. Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

      Tech Tips

      Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

    6. Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

      Tech Tips

      Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

  4. REMOVE FRONT DRIVE SHAFT ASSEMBLY

    Click here

  5. REMOVE REAR ENGINE MOUNTING BRACKET (for 2WD)

    Click here

  6. REMOVE FRONT DRIVE SHAFT OIL SEAL LH


    1. A002BAKN01

      Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.

      SST
      09308-00010

      Note

      Be careful not to damage the automatic transaxle case sub-assembly.

  7. REMOVE FRONT DRIVE SHAFT OIL SEAL RH


    1. A0027LON01

      Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

      SST
      09308-00010

      Note

      Be careful not to damage the transaxle housing.

  8. INSTALL FRONT DRIVE SHAFT OIL SEAL RH


    1. A002AEPC01
      *a Depth

      Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

      SST
      09316-60011   ( 09316-00011 )
      09950-70010   ( 09951-07150 )
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Note


      • Make sure that the front drive shaft oil seal RH is installed in the correct direction.

      • Do not damage the lip of the front drive shaft oil seal RH.

  9. INSTALL FRONT DRIVE SHAFT OIL SEAL LH


    1. A002CAWC01
      *a Depth

      Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

      SST
      09316-10010
      09950-70010   ( 09951-07100 )
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      Note


      • Make sure that the front drive shaft oil seal LH is installed in the correct direction.

      • Do not damage the lip of the front drive shaft oil seal LH.

  10. INSTALL REAR ENGINE MOUNTING BRACKET (for 2WD)

    Click here

  11. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click here

  12. ADJUST AUTOMATIC TRANSAXLE FLUID

    Click here

  13. INSPECT FOR FLUID LEAK

  14. INSTALL FRONT FENDER APRON SEAL LH

    Click here

  15. INSTALL NO. 1 ENGINE UNDER COVER

    Click here