AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P271314

DTC Code DTC Name
P271314 Pressure Control Solenoid "D" Circuit Short to Ground or Open

DESCRIPTION

Refer to DTC P27137F.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P271314 Pressure Control Solenoid "D" Circuit Short to Ground or Open

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. Engine is running

  2. Solenoid (SLT) valve circuit is open or short to ground

  3. 1 second

  4. 1-trip detection logic

  • Solenoid (SLT) valve

  • Transmission wire

  • Harness and connector

  • ECM

 Comes on DTC stored

SAE Code:

P2720

MONITOR DESCRIPTION

When an open or short to ground in the solenoid (SLT) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.

WIRING DIAGRAM

Refer to DTC P271312.

Click here

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click here

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Start the engine.

  2. Check for DTCs again.

    Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLT) VALVE) - ECM)


    1. Disconnect the C1 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C1-67 (SLT+) - C1-37 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
      C1-67 (SLT+) or C1-37 (SLT-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) Click here

    OK

  2. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM REGISTRATION Click here

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the C62 transmission wire connector.

    2. Disconnect the C1 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C62-24 (SLT+) - C1-67 (SLT+) Always Below 1 Ω
      C62-23 (SLT-) - C1-37 (SLT-) Always Below 1 Ω
      C62-24 (SLT+) or C1-67 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
      C62-23 (SLT-) or C1-37 (SLT-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

    OK

  4. INSPECT SOLENOID (SLT) VALVE


    1. B003Z4NC76
      *a

      Component without harness connected

      (Solenoid (SLT) Valve)

      Remove the solenoid (SLT) valve.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Solenoid (SLT) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE TRANSMISSION WIRE When Not Using the Engine Support Bridge: Click here
    REPAIR OR REPLACE TRANSMISSION WIRE When Using the Engine Support Bridge: Click here

    NG

    REPLACE SOLENOID (SLT) VALVE Click here