AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P056014

DTC Code DTC Name
P056014 System Voltage Circuit Short to Ground or Open

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history and freeze frame data. If the battery voltage falls below a minimum level, the stored ECM data will be cleared and the ECM will determine that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P056014 System Voltage Circuit Short to Ground or Open

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. Always

  2. Low ECM back-up power source circuit voltage

  3. 3 seconds or more

  4. 1-trip detection logic

  • Back-up power source circuit

  • Battery terminals

  • Battery

  • ECM

 Comes on DTC stored

SAE Code:

P0562

Tech Tips

If DTC P056014 is stored, the ECM will not store other DTCs.

WIRING DIAGRAM

A002BZKE04
*a FL MAIN
*b EFI-MAIN
*c EFI NO. 1
*d Battery

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

    Click here

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the ignition switch to ON and wait for 3 seconds or more.

  2. Check for DTCs again.

    Click here

PROCEDURE


  1. INSPECT BATTERY


    1. Check that the battery is not depleted.

      Click here

      OK
      Battery is not depleted.
      Result
      Proceed to
      OK
      NG

    NG

    CHARGE OR REPLACE BATTERY

    OK

  2. CHECK BATTERY TERMINAL


    1. Check that the battery terminals are not loose or corroded.

      OK
      Battery terminals are not loose or corroded.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE BATTERY TERMINAL

    OK

  3. CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)


    1. A002BJ7C80
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the A43 ECM connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A43-1 (BATT) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

    OK

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here


      Powertrain > Transmission > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Wait 5 seconds or more.

    9. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    10. Read the DTCs.

      Result
      Result Proceed to
      DTC P056014 is output A
      DTCs are not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM REGISTRATION Click here