REPAIR INSTRUCTION INITIALIZATION


  1. PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

    Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
    Correct the steering angle neutral point Parking Assist Monitor System

    Click here

    Back door lock*1 Power door lock control system

    Click here

    Servo motor initialization Air Conditioning System (for Automatic Air Conditioning System)

    Click here

    Servo motor initialization Air Conditioning System (for Manual Air Conditioning System)

    Click here

    Reset back door close position*2 Power Back Door System

    Click here


    • *1: w/o Power Back Door System

    • *2: w/ Power Back Door System

    Note


    • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 90 second*1 or 120 seconds*2 before disconnecting the cable from the negative (-) battery terminal. (for Radio and Display Type)

      *1: w/ Toyota Link Function

      *2: w/o Toyota Link Function

    • After the engine switch is turned off, the navigation receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 90 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation Receiver Type)

  2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

    Replacement Part Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed Link
    ECM Vehicle Identification Number (VIN) registration MIL comes on

    Click here for 2GR-FE
    ECU communication ID registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.

    • Throttle body with motor assembly

    • Cleaning the deposits from the throttle body with motor assembly

    • Engine assembly

    • Cylinder head sub-assembly

    • Camshaft (for intake or exhaust camshaft)

    • Camshaft timing gear assembly

    • Camshaft timing exhaust gear assembly

    • Piston or piston ring

    • Mass air flow meter sub-assembly

    • Fuel injector assembly

    • Fuel pump

    • Air fuel ratio sensor

    • Engine coolant temperature sensor

    • Spark plug

    • Ignition coil assembly

    • Air leaks from intake system

    • Gas leaks from exhaust system

    • Knock control sensor

    		 Inspection after repair

    • Poor idle, etc.

    • Engine start function, etc.

    Click here for 1AR-FE

    • Throttle body with motor assembly

    • Cleaning the deposits from the throttle body with motor assembly

    • Engine assembly

    • Cylinder head sub-assembly

    • Camshaft (for intake or exhaust camshaft)

    • Camshaft timing gear assembly

    • Camshaft timing exhaust gear assembly

    • Piston or piston ring

    • Mass air flow meter sub-assembly

    • Fuel injector assembly

    • Fuel pump

    • Air fuel ratio sensor

    • Engine coolant temperature sensor

    • Spark plug

    • Ignition coil assembly

    • Air leaks from intake system

    • Gas leaks from exhaust system

    • Knock control sensor

    		 Inspection after repair

    • Poor idle, etc.

    • Engine start function, etc.

    Click here for 2GR-FE
    Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly

    • Dynamic radar cruise control system

    • Pre-crash safety system

    Click here

    Lane departure warning camera Adjust lane departure warning camera Lane departure alert system

    Click here

    Automatic transaxle assembly

    1. Reset memory

    2. Input transaxle compensation code into TCM

    3. Perform road test to allow TCM to learn

    • Large shift shock

    • Deterioration of fuel efficiency

    Click here for U660E Initialization

    Click here for U660E Registration

    Click here for U660F Initialization

    Click here for U660F Registration

    • Valve body assembly

    • Shift solenoid valve SL3 and/or SL4

    1. Reset memory

    2. Reset transaxle compensation code

    3. Perform road test to allow TCM to learn

    • Large shift shock

    • Deterioration of fuel efficiency
    Shift solenoid valve SL1 and/or SL2 form road test to allow TCM to learn

    • Large shift shock

    • Deterioration of fuel efficiency

    TCM

    (If possible, read the transaxle compensation code from the previous TCM)

    		 Possible

    1. Reset memory

    2. Transfer transaxle compensation code

    3. Perform road test to allow TCM to learn

    • Large shift shock

    • Deterioration of fuel efficiency
    Impossible

    1. Reset memory

    2. Reset transaxle compensation code

    3. Perform road test to allow TCM to learn

    • Large shift shock

    • Deterioration of fuel efficiency
    Automatic transaxle assembly

    1. Reset memory

    2. Input transaxle compensation code into ECM

    3. Perform road test to allow ECM to learn

    • Large shift shock

    • Deterioration of fuel efficiency

    Click here for U760E Initialization

    Click here for U760E Registration

    • Valve body assembly

    • Shift solenoid valve SL3 and/or SL4

    1. Reset memory

    2. Reset transaxle compensation code

    3. Perform road test to allow ECM to learn

    • Large shift shock

    • Deterioration of fuel efficiency
    Shift solenoid valve SL1 and/or SL2 Perform road test to allow ECM to learn

    • Large shift shock

    • Deterioration of fuel efficiency

    ECM

    (If possible, read the transaxle compensation code from the previous ECM)

    		 Possible

    1. Reset memory

    2. Transfer transaxle compensation code

    3. Perform road test to allow ECM to learn

    • Large shift shock

    • Deterioration of fuel efficiency
    Impossible

    1. Reset memory

    2. Reset transaxle compensation code

    3. Perform road test to allow ECM to learn

    • Large shift shock

    • Deterioration of fuel efficiency

    • 4WD ECU assembly*1

    • Acceleration sensor (airbag sensor assembly)

    		 Perform calibration AWD initial performance (acceleration, etc)

    Click here

    Skid control ECU (brake actuator assembly)

    1. Clear zero point calibration data and store system information.

    2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

    • VSC disabled or malfunctioning

    • DTCs are output

    • Slip indicator light illuminated

    • ABS warning light illuminated

    Click here

    Yaw rate and acceleration sensor (airbag sensor assembly)

    1. Clear zero point calibration data and store system information.

    2. Perform yaw rate and acceleration sensor zero point calibration and store system information.
    Power steering ECU assembly Assist map writing

    • DTCs are output

    • EPS control

    • EPS warning light illuminated

    Click here

    Steering sensor

    • Steering angle neutral point (Initialize parking assist monitor system)

    • Steering angle setting

    		 Parking assist monitor system

    Click here for Initialization

    Click here for Calibration
    Suspension, tires, etc. Television camera assembly optical axis (Back camera position setting)
    Television camera assembly

    • Parking assist monitor system initialization

    • Television camera assembly optical axis (Back camera position setting)
    Blind spot monitor sensor Blind spot monitor beam axis inspection DTCs are output

    Click here


    • Certification ECU (smart key ECU assembly)*2

    • ID code box (immobiliser code ECU)*2*4

    • Steering lock ECU (steering lock actuator assembly)*2

    • Electrical key transmitter sub-assembly*2

    • ECM*2

    • Main body ECU (multiplex network body ECU)*2

    		 Code registration (Immobiliser system (w/ Smart Entry and Start System))

    • Wireless door lock control system

    • Smart entry and start system

    • Engine start

    • Steering lock system

    		 See the Service Bulletin for the registration method.

    • Transponder key ECU assembly*3

    • Door control receiver

    • ECM*3

    		 Code registration (Immobiliser system (w/o Smart Entry and Start System))

    • Wireless door lock control system

    • Engine start

    		 See the Service Bulletin for the registration method.

    • Door control transmitter module set sub-assembly

    • Door control receiver

    		 Code registration (Wireless door lock system (w/o Smart Entry and Start System)) Wireless door lock control system

    Click here*3

    • No. 1 air conditioning radiator damper servo sub-assembly

    • No. 2 air conditioning radiator damper servo sub-assembly

    • Rear air mix damper servo sub-assembly

    • Rear mode damper servo sub-assembly

    • Blower damper servo sub-assembly

    		 Initialization servo motor (Air conditioning system (for Automatic Air Conditioning System)) DTCs are output

    Click here*5

    • No. 1 air conditioning radiator damper servo sub-assembly

    • Rear air mix damper servo sub-assembly

    • Rear mode damper servo sub-assembly

    • Blower damper servo sub-assembly

    		 Initialization servo motor (Air conditioning system (for Manual Air Conditioning System)) DTCs are output

    Click here*6

    • Door window regulator assembly

    • Power window regulator motor assembly

    • Door glass

    • Door glass run

    		 Initialize power window control system (for Models with Jam Protection Function on 4 Windows)

    • Auto up and down function

    • Jam protection function

    • Remote control function

    • Key-linked function

    • Wireless transmitter-linked function

    • Key-off operation function

    Click here*7

    • Door window regulator assembly

    • Power window regulator motor assembly (for driver door)

    • Power window regulator motor assembly (for front passenger door)

    • Door glass

    • Door glass run

    		 Initialize power window control system (for Models with Jam Protection Function on Front Door Windows)

    • Auto up and down function

    • Jam protection function

    • Remote control function

    • Key-linked function

    • Wireless transmitter-linked function

    • Key-off operation function

    Click here*8

    • Sliding roof ECU (sliding roof drive gear sub-assembly)

    • Sliding roof glass sub-assembly

    • Sliding roof drive cable sub-assembly

    		 Initialize sliding roof system

    • Auto operation function

    • Jam protection function

    • Key-off operation function

    • Key-linked function

    • Wireless transmitter-linked function

    • Sliding roof open warning function

    Click here


    • Multiplex network door ECU*9

    • Power back door unit assembly set LH or RH*9

    • Back door lock assembly*9

    		 Reset back door close position Power back door system

    Click here

    Headlight leveling ECU assembly*10

    • Synchronize the vehicle information

    • Perform headlight leveling ECU assembly initialization

    		 Headlight leveling function

    Click here

    Rear height control sensor sub-assembly*10 Perform headlight leveling ECU assembly initialization Headlight leveling function

    • *1: When the 4WD ECU assembly is replaced with a new one, calibration is unnecessary.

    • *2: w/ Smart entry and start system

    • *3: w/o Smart entry and start system

    • *4: w/ Rear Seat Heater

    • *5: for Automatic Air Conditioning System

    • *6: for Manual Air Conditioning System

    • *7: w/ Jam Protection Function on 4 Windows

    • *8: w/ Jam Protection Function on Front Door Windows

    • *9: w/ Power Back Door System

    • *10: w/ Automatic Headlight Beam Level Control System