CAUTION / NOTICE / HINT
Tech Tips
If the lane departure warning camera is replaced or removed and installed, or the toe-in is adjusted, perform lane departure warning camera adjustment.
PROCEDURE
ADJUST LANE DEPARTURE WARNING CAMERA (for LHD)
Prepare for camera axis learning.
Move the vehicle to a level surface.
Make sure the engine oil in the vehicle is at the specified level.
Make sure the engine coolant in the vehicle is at the specified level.
Make sure the fuel tank is full.
Make sure the spare tire is in the vehicle.
Make sure the standard tools are in the vehicle.
Make sure nobody is in the vehicle.
Make sure no extra loads are in the vehicle.
Adjust the tire pressures to the specified pressure.
Clean the windshield.
Perform front wheel alignment adjustment.
Perform front wheel alignment adjustment.
Note
Perform this procedure as accurately as possible.
Perform rear wheel alignment adjustment.
Perform rear wheel alignment adjustment.
Note
Perform this procedure as accurately as possible.
Create a target sheet.
*a | 16 mm (0.630 in.) |
*b | 80 mm (3.15 in.) |
*c | 160 mm (6.30 in.) |
Print or copy the illustration. Check that the dimensions are within +/- 5 mm (0.197 in.) of the ones in the table below.
Note
Make sure that the black areas of the target sheet are not glossy.
Make sure that the borders of the black and white areas on the target sheet are straight, and are not warped or blurry.
If the dimensions of the print or copy are not as specified, adjust settings and reprint or recopy so that the dimensions are as specified.
*a | Target Sheet |
*b | Cardboard |
Attach the target sheet.
Place the prepared target sheet on a piece of cardboard of the same size with the black area on the top right, as shown in the illustration. Then use double-sided tape to secure the target sheet in place.
Note
Do not attach reflective tape, such as transparent adhesive tape, to the target face, as this may affect target recognition.
*a | Pointed Tip Weight |
*b | Mark-off Line |
Hang a weight with a pointed tip from the center of the target sheet. Then, with double-sided tape, attach the target sheet to the reflector so that the weight aligns with the mark-off line of SST (laser radar adjusting reflector).
Note
Perform this procedure as accurately as possible.
Attach the target sheet so that it is horizontal with the ground.
*a | 1350 mm (4.43 ft.) |
Move the reflector up and down to position the center of the target at the height shown in the illustration and secure it in place.
Note
Perform this procedure as accurately as possible.
Measure the target placement point.
Note
Do not place black and white patterned objects near the target.
Face the vehicle toward a wall with no patterns or make sure the background behind the target has no patterns.
Perform this procedure as accurately as possible.
Do not place reflective materials in the area behind the target.
Make sure the distance between the target and wall is within 3 m (9.84 ft.).
Make sure the shadow of the target is not on the wall as this may cause a recognition error.
Hang the string (with weight) from the center of the vehicle rear emblem. Mark the vehicle rear center point on the ground.
*a | String | *b | Weight |
*c | Center point | *d | Point A |
Repeat for the front of the vehicle.
*a | String | *b | Weight |
*c | Center point | *d | Point B |
Secure one end of a string to point A, stretch the other end so that it passes point B in a straight line, and secure the string at a position 2000 mm (6.56 ft.) or more from the front end of the vehicle.
Tech Tips
Make sure the string is taut (using tape, etc.) when it is secured.
Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.
Mark point C at a position 602 mm (1.97 ft.) from point B.
*a | Point A | *b | Point B |
*c | Point C | *d | Point D |
*e | Line E | *f | Line F |
*g | Point G (Placement Point 2) | *h | Line H |
*i | Line I | *j | Point J (Placement Point 3) |
*k | Tape | *l | String |
*m | 602 mm (1.97 ft.) | *n | 1852 mm (6.07 ft.) |
Mark point D at a position 1852 mm (6.07 ft.) from point B.
Using a string, mark line E at a position 1000 mm (3.28 ft.) from point C.
Using a string, mark line H at a position 1000 mm (3.28 ft.) from point C.
Using a string, mark line F at a position 1000 mm (3.28 ft.) from point D.
Using a string, mark line I at a position 1000 mm (3.28 ft.) from point D.
Mark point G at the point where line E and line F intersect (placement point 2).
Mark point J at the point where line H and line I intersect (placement point 3).
Secure a string that connects point G and point J to the ground (target placement line).
*a | Point A | *b | Point B |
*c | Point C | *d | Point D |
*e | String | *f | Tape |
*g | Point G (Placement Point 2) | *h | 602 mm (1.97 ft.) |
*i | 1227 mm (4.02 ft.) | *j | Point J (Placement Point 3) |
*k | Point K (Placement Point 1) | *l | 1852 mm (6.07 ft.) |
*m | Target Placement Line | - | - |
Mark point K at the intersection between the string connecting points C and D and the string connecting points G and J (placement point 1).
Confirm the distance measurements for points K, G, and J (placement points 1, 2, and 3) again.
*a | Point A | *b | Point B |
*c | Point C | *d | Point D |
*e | Line E | *f | Line F |
*g | Point G (Placement Point 2) | *h | Line H |
*i | Line I | *j | Point J (Placement Point 3) |
*k | Point K (Placement Point 1) | *l | Tape |
*m | String | *n | 1000 mm (3.28 ft.) (String) |
*o | 95 mm (3.74 in.) | *p | 3000 mm (9.84 ft.) |
*q | 1852 mm (6.07 ft.) | *r | 1227 mm (4.02 ft.) |
*s | 602 mm (1.97 ft.) | *t | Lane Departure Warning Camera Position |
Memorize camera/target position.
Note
Close all doors.
Perform the procedure with no one in the vehicle.
During the procedure, do not lean on the vehicle.
Do not turn on the headlights.
When using the GTS:
Connect the GTS to the DLC3.
Turn the ignition switch on (IG).*1
Turn the GTS on.
Select "Connect to Vehicle".
Select each item on the display screen and proceed to the next screen.
Under "System Selection Menu", select "Lane Departure Alert".
Select "Utility" from the display screen.
Select "Recognition Camera/Target Position Memory" and proceed to the next screen.
Tech Tips
A buzzer will sound for 1 second.
Follow the GTS display, and continue with the adjustment.
Tester Display |
---|
Recognition Camera/Target Position Memory |
Input the height of the camera "1518 mm (59.8 in.)" and the horizontal position of the camera "95 mm (3.74 in.)" into the input screen. Then press the "Next" button on the display screen.
Input "3000 mm (118 in.)" for the distance from the camera to the target and "1350 mm (53.1 in.)" for the height of the target into the input screen. Then press the "Next" button on the display screen.
Input "1911 mm (75.2 in.)" for the width of the vehicle and "816 mm (32.1 in.)" for the distance between the recognition camera and the front tire into the input screen. Then press the "Next" button on the display screen.
Press the "Exit" button to finish the camera/target position memory mode.
Note
If "Error Camera/target position memory" is displayed on the screen, press the "Try Again" button, and repeat from procedure *1 again.
Perform camera axis learning.
Select "Connect to Vehicle".
Select each item on the display screen and proceed to the next screen.
Under "System Selection Menu", select "Lane Departure Alert".*1
Select "Utility" from the display screen.
Select "Recognition Camera Axis Adjust" from the display screen.
Follow the GTS display and continue with the adjustment.
Tester Display |
---|
Recognition Camera Axis Adjust |
*a | Mark-off Line |
*b | Point K (Placement Point 1) |
*c | Target Placement Line |
Align the target sheet with the target placement line and align the mark-off line with point K (placement point 1).
Check that the screen displays camera axis learning for target 1, then press the "Next" button on the display screen.
*a | Mark-off Line |
*b | Point G (Placement Point 2) |
*c | Target Placement Line |
Align the target sheet with the target placement line, and align the mark-off line with point G (placement point 2).
Check that the screen displays camera axis learning for target 2, then press the "Next" button on the display screen.
Note
Within 3 minutes after the screen displays the camera axis learning for target 2, move the target and press the "Next" button on the display screen.
*a | Mark-off Line |
*b | Point J (Placement Point 3) |
*c | Target Placement Line |
Align the target sheet with the target placement line and align the mark-off line with point J (placement point 3).
Check that the screen displays camera axis learning for target 3 then press the "Next" button on the display screen.
Note
Within 3 minutes after the screen displays the camera axis learning for target 3, move the target and press the "Next" button on the display screen.
Press the "Exit" button to finish camera axis learning mode.
Note
If "Error camera axis adjust" is displayed on the screen, press the "Exit" button. Then after checking the following, turn the ignition switch on (IG) and off, and repeat from procedure *1 again.Height of the target.
Distance from the lane departure warning camera to the target.
Orientation of the target (black area positioned on top right).
If surrounding area is bright enough.
If black and white patterned objects are placed near the target.
ADJUST LANE DEPARTURE WARNING CAMERA (for RHD)
Prepare for camera axis learning.
Move the vehicle to a level surface.
Make sure the engine oil in the vehicle is at the specified level.
Make sure the engine coolant in the vehicle is at the specified level.
Make sure the fuel tank is full.
Make sure the spare tire is in the vehicle.
Make sure the standard tools are in the vehicle.
Make sure nobody is in the vehicle.
Make sure no extra loads are in the vehicle.
Adjust the tire pressures to the specified pressure.
Clean the windshield.
Perform front wheel alignment adjustment.
Perform front wheel alignment adjustment.
Note
Perform this procedure as accurately as possible.
Perform rear wheel alignment adjustment.
Perform rear wheel alignment adjustment.
Note
Perform this procedure as accurately as possible.
Create a target sheet.
*a | 16 mm (0.630 in.) |
*b | 80 mm (3.15 in.) |
*c | 160 mm (6.30 in.) |
Print or copy the illustration. Check that the dimensions are within +/- 5 mm (0.197 in.) of the ones in the table below.
Note
Make sure that the black areas of the target sheet are not glossy.
Make sure that the borders of the black and white areas on the target sheet are straight, and are not warped or blurry.
If the dimensions of the print or copy are not as specified, adjust settings and reprint or recopy so that the dimensions are as specified.
*a | Target Sheet |
*b | Cardboard |
Attach the target sheet.
Place the prepared target sheet on a piece of cardboard of the same size with the black area on the top right, as shown in the illustration. Then use double-sided tape to secure the target sheet in place.
Note
Do not attach reflective tape, such as transparent adhesive tape, to the target face, as this may affect target recognition.
*a | Pointed Tip Weight |
*b | Mark-off Line |
Hang a weight with a pointed tip from the center of the target sheet. Then, with double-sided tape, attach the target sheet to the reflector so that the weight aligns with the mark-off line of SST (laser radar adjusting reflector).
Note
Perform this procedure as accurately as possible.
Attach the target sheet so that it is horizontal with the ground.
*a | 1350 mm (4.43 ft.) |
Move the reflector up and down to position the center of the target at the height shown in the illustration and secure it in place.
Note
Perform this procedure as accurately as possible.
Measure the target placement point.
Note
Do not place black and white patterned objects near the target.
Face the vehicle toward a wall with no patterns or make sure the background behind the target has no patterns.
Perform this procedure as accurately as possible.
Do not place reflective materials in the area behind the target.
Make sure the distance between the target and wall is within 3 m (9.84 ft.).
Make sure the shadow of the target is not on the wall as this may cause a recognition error.
Hang the string (with weight) from the center of the vehicle rear emblem. Mark the vehicle rear center point on the ground.
*a | String | *b | Weight |
*c | Center point | *d | Point A |
Repeat for the front of the vehicle.
*a | String | *b | Weight |
*c | Center point | *d | Point B |
Secure one end of a string to point A, stretch the other end so that it passes point B in a straight line, and secure the string at a position 2000 mm (6.56 ft.) or more from the front end of the vehicle.
Tech Tips
Make sure the string is taut (using tape, etc.) when it is secured.
Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.
Mark point C at a position 602 mm (1.97 ft.) from point B.
*a | Point A | *b | Point B |
*c | Point C | *d | Point D |
*e | Line E | *f | Line F |
*g | Point G (Placement Point 2) | *h | Line H |
*i | Line I | *j | Point J (Placement Point 3) |
*k | Tape | *l | String |
*m | 602 mm (1.97 ft.) | *n | 1852 mm (6.07 ft.) |
Mark point D at a position 1852 mm (6.07 ft.) from point B.
Using a string, mark line E at a position 1000 mm (3.28 ft.) from point C.
Using a string, mark line H at a position 1000 mm (3.28 ft.) from point C.
Using a string, mark line F at a position 1000 mm (3.28 ft.) from point D.
Using a string, mark line I at a position 1000 mm (3.28 ft.) from point D.
Mark point G at the point where line E and line F intersect (placement point 2).
Mark point J at the point where line H and line I intersect (placement point 3).
Secure a string that connects point G and point J to the ground (target placement line).
*a | Point A | *b | Point B |
*c | Point C | *d | Point D |
*e | String | *f | Tape |
*g | Point G (Placement Point 2) | *h | 602 mm (1.97 ft.) |
*i | 1227 mm (4.02 ft.) | *j | Point J (Placement Point 3) |
*k | Point K (Placement Point 1) | *l | 1852 mm (6.07 ft.) |
*m | Target Placement Line | - | - |
Mark point K at the intersection between the string connecting points C and D and the string connecting points G and J (placement point 1).
Confirm the distance measurements for points K, G, and J (placement points 1, 2, and 3) again.
*a | Point A | *b | Point B |
*c | Point C | *d | Point D |
*e | Line E | *f | Line F |
*g | Point G (Placement Point 2) | *h | Line H |
*i | Line I | *j | Point J (Placement Point 3) |
*k | Point K (Placement Point 1) | *l | Tape |
*m | String | *n | 1000 mm (3.28 ft.) (String) |
*o | 79 mm (3.11 in.) | *p | 3000 mm (9.84 ft.) |
*q | 1852 mm (6.07 ft.) | *r | 1227 mm (4.02 ft.) |
*s | 602 mm (1.97 ft.) | *t | Lane Departure Warning Camera Position |
Memorize camera/target position.
Note
Close all doors.
Perform the procedure with no one in the vehicle.
During the procedure, do not lean on the vehicle.
Do not turn on the headlights.
When using the GTS:
Connect the GTS to the DLC3.
Turn the ignition switch on (IG).*1
Turn the GTS on.
Select "Connect to Vehicle".
Select each item on the display screen and proceed to the next screen.
Under "System Selection Menu", select "Lane Departure Alert".
Select "Utility" from the display screen.
Select "Recognition Camera/Target Position Memory" and proceed to the next screen.
Tech Tips
A buzzer will sound for 1 second.
Follow the GTS display, and continue with the adjustment.
Tester Display |
---|
Recognition Camera/Target Position Memory |
Input the height of the camera "1518 mm (59.8 in.)" and the horizontal position of the camera "-79 mm (-3.11 in.)" into the input screen. Then press the "Next" button on the display screen.
Input "3000 mm (118 in.)" for the distance from the camera to the target and "1350 mm (53.1 in.)" for the height of the target into the input screen. Then press the "Next" button on the display screen.
Input "1911 mm (75.2 in.)" for the width of the vehicle and "816 mm (32.1 in.)" for the distance between the recognition camera and the front tire into the input screen. Then press the "Next" button on the display screen.
Press the "Exit" button to finish the camera/target position memory mode.
Note
If "Error Camera/target position memory" is displayed on the screen, press the "Try Again" button, and repeat from procedure *1 again.
Perform camera axis learning.
Select "Connect to Vehicle".
Select each item on the display screen and proceed to the next screen.
Under "System Selection Menu", select "Lane Departure Alert".*1
Select "Utility" from the display screen.
Select "Recognition Camera Axis Adjust" from the display screen.
Follow the GTS display and continue with the adjustment.
Tester Display |
---|
Recognition Camera Axis Adjust |
*a | Mark-off Line |
*b | Point K (Placement Point 1) |
*c | Target Placement Line |
Align the target sheet with the target placement line and align the mark-off line with point K (placement point 1).
Check that the screen displays camera axis learning for target 1, then press the "Next" button on the display screen.
*a | Mark-off Line |
*b | Point G (Placement Point 2) |
*c | Target Placement Line |
Align the target sheet with the target placement line, and align the mark-off line with point G (placement point 2).
Check that the screen displays camera axis learning for target 2, then press the "Next" button on the display screen.
Note
Within 3 minutes after the screen displays the camera axis learning for target 2, move the target and press the "Next" button on the display screen.
*a | Mark-off Line |
*b | Point J (Placement Point 3) |
*c | Target Placement Line |
Align the target sheet with the target placement line and align the mark-off line with point J (placement point 3).
Check that the screen displays camera axis learning for target 3 then press the "Next" button on the display screen.
Note
Within 3 minutes after the screen displays the camera axis learning for target 3, move the target and press the "Next" button on the display screen.
Press the "Exit" button to finish camera axis learning mode.
Note
If "Error camera axis adjust" is displayed on the screen, press the "Exit" button. Then after checking the following, turn the ignition switch on (IG) and off, and repeat from procedure *1 again.Height of the target.
Distance from the lane departure warning camera to the target.
Orientation of the target (black area positioned on top right).
If surrounding area is bright enough.
If black and white patterned objects are placed near the target.