ВЕНТИЛЯТОР СИСТЕМЫ ОХЛАЖДЕНИЯ Cooling Fan Circuit

DESCRIPTION

The ECM turns the fan relays on or off using signals based on the engine coolant temperature, air conditioning switch condition (on/off) (w/ Air Conditioning System) and refrigerant pressure (w/ Air Conditioning System), as well as the engine speed and vehicle speed signals.

The ECM switches the circuit of the cooling fan motors between series and parallel by turning on or off the fan relays in order to control the speed of the cooling fan motors in two steps.

WIRING DIAGRAM

Refer to the System Diagram.

Click here

CAUTION / NOTICE / HINT

PROCEDURE

1. PERFORM ACTIVE TEST USING GTS

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the ignition switch to ON.

   3. Turn the GTS on.

   4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan High Speed

      
      Powertrain > Engine and ECT > Active Test

      Tester Display
      Actuator Test of Fan High Speed

   5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan Low Speed

      
      Powertrain > Engine and ECT > Active Test

      Tester Display
      Actuator Test of Fan Low Speed

   6. Perform the Active Test according to the display on the GTS.

      OK
      Tester Operation Fan Operation ON (Actuator Test of Fan High Speed) Cooling fans operate in high speed ON (Actuator Test of Fan Low Speed) Cooling fans operate in low speed OFF Cooling fans stop

      Result
      Proceed to OK NG

   
   

   OK

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

   NG

2. CHECK HARNESS AND CONNECTOR (FANL - FANH POWER SOURCE)

   
   

   1. Disconnect the A62 ECM connector.

   2. Turn the ignition switch to ON.

   3. 

      *a	Front view of wire harness connector (to ECM)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition A62-45 (FANH) - Body ground Ignition switch ON 11 to 14 V A62-20 (FANL) - Body ground Ignition switch ON 11 to 14 V

      Result
      Proceed to OK NG

   
   

   NG

   INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3) Click here

   OK

3. CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)

   
   
   1. 

      *1	No. 2 Engine Room Relay Block and Junction Block Assembly
      *2	FAN NO. 1 Relay
      *3	FAN NO. 3 Relay

      Remove the FAN NO. 1 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.

   2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition 3 (FAN NO. 1 relay) - Body ground Always 11 to 14 V 3 (FAN NO. 3 relay) - Body ground Always 11 to 14 V

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)

   OK

4. INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)

   
   

   1. Inspect the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay.

      Click here

      Result
      Result Proceed to OK A NG (FAN NO. 1 relay) B NG (FAN NO. 2 relay) C NG (FAN NO. 3 relay) D

   
   

   B

   REPLACE FAN NO. 1 RELAY

   C

   REPLACE FAN NO. 2 RELAY

   D

   REPLACE FAN NO. 3 RELAY

   A

5. CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

   
   
   1. 

      *1	No. 2 Engine Room Relay Block and Junction Block Assembly
      *2	FAN NO. 2 Relay

      Remove the FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition 5 (FAN NO. 2 relay) - Body ground Always Below 1 Ω

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

   OK

6. INSPECT COOLING FAN MOTOR

   
   

   1. Inspect the cooling fan motor.

      Click here

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE COOLING FAN MOTOR Click here

   OK

7. CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

   
   

   1. Disconnect the A52 cooling fan motor connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition A52-1 - Body ground Always Below 1 Ω

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

   OK

8. CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

   
   

   1. Disconnect the A52 cooling fan motor connector.

   2. 

      *1	No. 2 Engine Room Relay Block and Junction Block Assembly
      *2	FAN NO. 1 Relay
      *3	FAN NO. 2 Relay

      Remove the FAN NO. 1 relay and FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition A52-2 - 5 (FAN NO. 1 relay) Always Below 1 Ω A52-2 - 4 (FAN NO. 2 relay) Always Below 1 Ω

      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition A52-2 or 5 (FAN NO. 1 relay) - Body ground Always 10 kΩ or higher A52-2 or 4 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

   OK

9. INSPECT NO. 2 COOLING FAN MOTOR

   
   

   1. Inspect the No. 2 cooling fan motor.

      Click here

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE NO. 2 COOLING FAN MOTOR Click here

   OK

10. CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

    
    

    1. Disconnect the A51 No. 2 cooling fan motor connector.

    2. 

       *1	No. 2 Engine Room Relay Block and Junction Block Assembly
       *2	FAN NO. 2 Relay
       *3	FAN NO. 3 Relay

       Remove the FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

       Standard Resistance (Check for Open)
       Tester Connection Condition Specified Condition A51-1 - 3 (FAN NO. 2 relay) Always Below 1 Ω A51-2 - 5 (FAN NO. 3 relay) Always Below 1 Ω

       Standard Resistance (Check for Short)
       Tester Connection Condition Specified Condition A51-1 or 3 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher A51-2 or 5 (FAN NO. 3 relay) - Body ground Always 10 kΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 COOLING FAN MOTOR - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

    OK

11. CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - FAN NO. 2 RELAY)

    
    
    1. 

       *1	No. 2 Engine Room Relay Block and Junction Block Assembly
       *2	FAN NO. 1 Relay
       *3	FAN NO. 2 Relay

       Remove the FAN NO. 1 relay and FAN NO. 2 relay from the No. 2 engine room relay block and junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance (Check for Open)
       Tester Connection Condition Specified Condition 1 (FAN NO. 1 relay) - 1 (FAN NO. 2 relay) Always Below 1 Ω 2 (FAN NO. 1 relay) - 2 (FAN NO. 2 relay) Always Below 1 Ω

       Standard Resistance (Check for Short)
       Tester Connection Condition Specified Condition 1 (FAN NO. 1 relay) or 1 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher 2 (FAN NO. 1 relay) or 2 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher

       Result
       Proceed to OK NG

    
    

    OK

    REPAIR OR REPLACE ECM Click here

    NG

    REPAIR OR REPLACE NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY

12. INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)

    
    

    1. Inspect the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay.

       Click here

       Result
       Result Proceed to OK A NG (FAN NO. 1 relay) B NG (FAN NO. 2 relay) C NG (FAN NO. 3 relay) D

    
    

    B

    REPLACE FAN NO. 1 RELAY

    C

    REPLACE FAN NO. 2 RELAY

    D

    REPLACE FAN NO. 3 RELAY

    A

13. CHECK HARNESS AND CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - ECM)

    
    
    1. 

       *1	No. 2 Engine Room Relay Block and Junction Block Assembly
       *2	FAN NO. 1 Relay
       *3	FAN NO. 2 Relay
       *4	FAN NO. 3 Relay

       Remove the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.

    2. Disconnect the A62 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

       Standard Resistance (Check for Open)
       Tester Connection Condition Specified Condition 2 (FAN NO. 1 relay) - A62-45 (FANH) Always Below 1 Ω 2 (FAN NO. 2 relay) - A62-45 (FANH) Always Below 1 Ω 2 (FAN NO. 3 relay) - A62-20 (FANL) Always Below 1 Ω

       Standard Resistance (Check for Short)
       Tester Connection Condition Specified Condition 2 (FAN NO. 1 relay) or A62-45 (FANH) - Body ground Always 10 kΩ or higher 2 (FAN NO. 2 relay) or A62-45 (FANH) - Body ground Always 10 kΩ or higher 2 (FAN NO. 3 relay) or A62-20 (FANL) - Body ground Always 10 kΩ or higher

       Result
       Proceed to OK NG

    
    

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY- ECM)