RELAY ON-VEHICLE INSPECTION

PROCEDURE


  1. INSPECT HEADLIGHT RELAY


    1. A00YUBO

      Remove the headlight relay from the engine room relay box LH.

    2. A01GAW0N01

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
        Battery voltage applied to terminals 1 and 2 Below 1 Ω

        If the result is not as specified, replace the headlight relay.

    3. Install the headlight relay to the engine room relay box LH.

  2. INSPECT HEADLIGHT DIMMER RELAY


    1. A00YW9B

      Remove the headlight dimmer relay from the engine room relay box LH.

    2. A01GAW0N01

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
        Battery voltage applied to terminals 1 and 2 Below 1 Ω

        If the result is not as specified, replace the headlight dimmer relay.

    3. Install the headlight dimmer relay to the engine room relay box LH.

  3. INSPECT FOG LIGHT RELAY (w/ Fog Light)


    1. A00YXTS

      Remove the fog light relay from the engine room relay box RH.

    2. A01GDFSN01

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
        Battery voltage applied to terminals 1 and 2 Below 1 Ω

        If the result is not as specified, replace the fog light relay.

    3. Install the fog light relay to the engine room relay box RH.

  4. INSPECT RUNNING LIGHT RELAY (w/ Daytime Running Light)


    1. A00YQVL

      Remove the running light relay from the engine room relay box RH.

    2. A01GDFSN01

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
        Battery voltage applied to terminals 1 and 2 Below 1 Ω

        If the result is not as specified, replace the running light relay.

    3. Install the running light relay to the engine room relay box RH.

  5. INSPECT REAR FOG LIGHT RELAY (for LHD)


    1. Remove the combination meter assembly.

      Click here

    2. A00YRH5

      Remove the rear fog light relay.

    3. A01GDFSN01

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
        Battery voltage applied to terminals 1 and 2 Below 1 Ω

        If the result is not as specified, replace the rear fog light relay.

    4. Install the rear fog light relay.

    5. Install the combination meter assembly.

      Click here

  6. INSPECT REAR FOG LIGHT RELAY (for RHD)


    1. Remove the combination meter assembly.

      Click here

    2. A00YWZ9

      Remove the rear fog light relay.

    3. A01GDFSN01

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
        Battery voltage applied to terminals 1 and 2 Below 1 Ω

        If the result is not as specified, replace the rear fog light relay.

    4. Install the rear fog light relay.

    5. Install the combination meter assembly.

      Click here