AIRBAG SYSTEM(w/o Occupant Classification System) Diagnosis Circuit

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

Tech Tips


  • When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

  • A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.

WIRING DIAGRAM

B0029JME03

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

  • After replacing the airbag sensor assembly, refer to initialization.

    Click here

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Check if a CAN communication DTC is output.


      Result
      Proceed to
      DTCs are output
      DTC is not output

    DTCs are output

    GO TO CAN COMMUNICATION SYSTEM for LHD with central gateway ECU Click here for RHD with central gateway ECU Click here for LHD without central gateway ECU Click here for RHD without central gateway ECU Click here

    DTC is not output

  2. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)


    1. Turn the ignition switch off.

      B002991C03
      *A for 2AR-FE, 3ZR-FE, 3ZR-FAE, 2WW *B for 2AD-FHV, 2AD-FTV
      *C for 2AR-FE, 3ZR-FE *D for 3ZR-FAE
      *E for 2WW - -
      *a Front view of DLC3 *b

      Front view of wire harness connector

      (to ECM)

    2. Disconnect the A62*1 or A61*2 connector from the ECM.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 2AR-FE, 3ZR-FE
      Tester Connection Condition Specified Condition
      G14-13 (TC) - A62-23 (TC) Always Below 1 Ω
      for 3ZR-FAE
      Tester Connection Condition Specified Condition
      G14-13 (TC) - A62-33 (TC) Always Below 1 Ω
      for 2AD-FHV, 2AD-FTV
      Tester Connection Condition Specified Condition
      G14-13 (TC) - A61-26 (TC) Always Below 1 Ω
      for 2WW
      Tester Connection Condition Specified Condition
      G14-13 (TC) - A62-50 (TC) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)


    1. B00297DC04
      *a Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G14-4 (CG) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    1. B0029LUC03
      *A for 2AR-FE, 3ZR-FE, 3ZR-FAE, 2WW
      *B for 2AD-FHV, 2AD-FTV
      *C for 2AR-FE, 3ZR-FE
      *D for 3ZR-FAE
      *E for 2WW
      *a

      Front view of wire harness connector

      (to ECM)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 2AR-FE, 3ZR-FE
      Tester Connection Condition Specified Condition
      A62-23 (TC) - Body ground Always Below 1 Ω
      for 3ZR-FAE
      Tester Connection Condition Specified Condition
      A62-33 (TC) - Body ground Always Below 1 Ω
      for 2AD-FHV, 2AD-FTV
      Tester Connection Condition Specified Condition
      A61-26 (TC) - Body ground Always Below 1 Ω
      for 2WW
      Tester Connection Condition Specified Condition
      A62-50 (TC) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU