METER / GAUGE SYSTEM, Diagnostic DTC:B150A

DTC Code DTC Name
B150A Lost Communication with HMI-LAN

DESCRIPTION


The combination meter assembly receives a text data signal from the radio and display receiver assembly*1 or navigation receiver assembly*2 via local bus communication.

Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B150A Lost Communication with HMI-LAN After the combination meter assembly receives a registration information signal, which is sent by the radio and display receiver assembly*1 or navigation receiver assembly*2 when the ignition switch is ON, 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more.

  • Harness or connector

  • Radio and display receiver assembly*1

  • Navigation receiver assembly*2

  • Combination meter assembly

WIRING DIAGRAM


  1. for Radio and Display Type

    A01V9YKE34
    *a Radio and Display Receiver Assembly
    *b Combination Meter Assembly
    *c CAN Communication Line

  2. for Navigation Receiver Type

    A01V9YKE33
    *a Navigation Receiver Assembly
    *b Combination Meter Assembly
    *c CAN Communication Line

CAUTION / NOTICE / HINT

Note


  • When replacing the combination meter assembly, make sure to replace it with a new one.

  • except 8 Speakers:

    Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for navigation system or audio and visual system.

    Audio and Visual System: Click here

    Navigation System: Click here

  • After replacing the radio receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).

PROCEDURE


  1. CONFIRM MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      w/ Navigation System A
      for Radio and Display Type B

    B

    CHECK FOR DTC (AUDIO AND VISUAL SYSTEM) Click here

    A

  2. CHECK FOR DTC (NAVIGATION SYSTEM)


    1. Check for DTCs.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      DTCs are not output.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO NAVIGATION SYSTEM Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)


    1. Disconnect the G16 combination meter assembly connector.

    2. Disconnect the G158 navigation receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G16-23 (MSCH) - G158-3 (CNH1) Always Below 1 Ω
      G16-22 (MSCL) - G158-4 (CNL1) Always Below 1 Ω
      G16-23 (MSCH) or G158-3 (CNH1) - Body ground Always 10 kΩ or higher
      G16-22 (MSCL) or G158-4 (CNL1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK COMBINATION METER ASSEMBLY


    1. Replace the combination meter assembly.

      Click here

    2. Turn the ignition switch to ON and wait 30 seconds.

      Note

      A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio receiver assembly.

    3. A01VAJPC03
      *a Multi-information Display
      *b Audio Tab

      Operate the steering pad switch assembly and check that the audio tab illuminates.

    4. Check for DTCs.

      Click here


      Body Electrical > Combination Meter > Trouble Codes
      OK
      The audio tab illuminates and DTC B150A is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

  5. CHECK FOR DTC (AUDIO AND VISUAL SYSTEM)


    1. Check for DTCs.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      DTCs are not output.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO AUDIO AND VISUAL SYSTEM Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)


    1. Disconnect the G16 combination meter assembly connector.

    2. Disconnect the G159 radio and display receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G16-23 (MSCH) -G159-3 (CNH1) Always Below 1 Ω
      G16-22 (MSCL) - G159-4 (CNL1) Always Below 1 Ω
      G16-23 (MSCH) or G159-3 (CNH1) - Body ground Always 10 kΩ or higher
      G16-22 (MSCL) or G159-4 (CNL1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK COMBINATION METER ASSEMBLY


    1. Replace the combination meter assembly.

      Click here

    2. Turn the ignition switch to ON and wait 30 seconds.

      Note

      A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio receiver assembly.

    3. A01VAJPC03
      *a Multi-information Display
      *b Audio Tab

      Operate the steering pad switch assembly and check that the audio tab illuminates.

    4. Check for DTCs.

      Click here


      Body Electrical > Combination Meter > Trouble Codes
      OK
      The audio tab illuminates and DTC B150A is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here