BLIND SPOT MONITOR SYSTEM HOW TO PROCEED WITH TROUBLESHOOTING

DTC Code DTC Name
HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

Tech Tips


  • Use the following procedure to troubleshoot the blind spot monitor system.

  • *: Use the GTS.

PROCEDURE


  1. VEHICLE BROUGHT TO WORKSHOP

    Result
    Proceed to
    NEXT

    NEXT

  2. CUSTOMER PROBLEM ANALYSIS

    Result
    Proceed to
    NEXT

    NEXT

  3. INSPECT BATTERY VOLTAGE


    1. Measure the battery voltage with the ignition switch off.

      Standard voltage
      11 to 14 V

      If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK CAN COMMUNICATION SYSTEM*


    1. Use the GTS to check if the CAN communication system is functioning normally.

      for LHD Click here

      for RHD Click here

      Result
      Proceed to
      CAN communication system DTC is not output.
      CAN communication system (for LHD) DTC is output.
      CAN communication system (for RHD) DTC is output.

    CAN communication system (for LHD) DTC is output.

    GO TO CAN COMMUNICATION SYSTEM Click here

    CAN communication system (for RHD) DTC is output.

    GO TO CAN COMMUNICATION SYSTEM Click here

    CAN communication system DTC is not output.

  5. CHECK FOR DTC AND FREEZE FRAME DATA*


    1. Refer to DTC Check / Clear for the blind spot monitor system.

      Click here


      Body Electrical > Blind Spot Monitor Slave > Clear DTCs
      Body Electrical > Blind Spot Monitor Master > Clear DTCs

    2. Record or print DTCs and freeze frame data, if necessary.

      Click here

      Result
      Proceed to
      DTCs are output.
      DTCs are not output.

    DTCs are not output.

    PERFORM SYMPTOMS TABLE Click here

    DTCs are output.

  6. CLEAR DTC*


    1. Refer to DTC Check / Clear for the blind spot monitor system.

      Click here

      Tech Tips

      The current DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.


      Body Electrical > Blind Spot Monitor Master > Clear DTCs
      Body Electrical > Blind Spot Monitor Slave > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  7. RECHECK FOR DTC*


    1. Refer to DTC Check / Clear for the blind spot monitor system.

      Click here


      Body Electrical > Blind Spot Monitor Master > Trouble Codes
      Body Electrical > Blind Spot Monitor Slave > Trouble Codes

      Tech Tips

      Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

      Result
      Proceed to
      DTCs are output.
      DTCs are not output.

    DTCs are not output.

    GO TO STEP 9 Click here

    DTCs are output.

  8. DIAGNOSTIC TROUBLE CODE CHART


    1. Find the output DTC in Diagnostic Trouble Code Chart.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 11 Click here

  9. PERFORM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table.

      Click here

      Tech Tips

      If the symptom does not recur and no DTC is output, attempt to reproduce the symptoms

      Click here

      Result
      Proceed to
      Fault is not listed in Problem Symptoms Table.
      Fault is listed in Problem Symptoms Table.

    Fault is listed in Problem Symptoms Table.

    ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE ADJUSTING LOCK NUT

    Fault is not listed in Problem Symptoms Table.

  10. PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*


    1. Refer to Terminals of ECU.

      Click here

    2. Refer to Data List / Active Test.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  11. CIRCUIT INSPECTION

    Result
    Proceed to
    NEXT

    NEXT

  12. ADJUST, REPAIR OR REPLACE

    Result
    Proceed to
    NEXT

    NEXT

  13. PERFORM BEAM AXIS INSPECTION AND CONFIRMATION


    1. Enter Test Mode (refer to Blind Spot Monitor Beam Axis Inspection).

      Click here

    2. Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  14. PERFORM CONFIRMATION TEST*

    Result
    Proceed to
    NEXT

    NEXT

    END