NAVIGATION SYSTEM(for SD), Diagnostic DTC:B1324

DTC Code DTC Name
B1324 Lost Communication with Meter

DESCRIPTION

This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the engine switch is on (ACC), 1 or more times, the navigation receiver assembly cannot receive the signal for 30 seconds or more.

  • Combination meter assembly

  • Navigation receiver assembly

  • Harness or connector

WIRING DIAGRAM

A01QQ0DE61
*a Combination Meter Assembly
*b Navigation Receiver Assembly
*c Local Bus Communication Line

CAUTION / NOTICE / HINT

Note


  • Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

    Click here

  • When replacing the combination meter assembly, make sure to replace it with a new one.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)


    1. Disconnect the G158 navigation receiver assembly connector.

    2. Disconnect the G16 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G158-3 (CNH1) - G16-23 (MSCH) Always Below 1 Ω
      G158-4 (CNL1) - G16-22 (MSCL) Always Below 1 Ω
      G158-3 (CNH1) - Body ground Always 10 kΩ or higher
      G158-4 (CNL1) - Body ground Always 10 kΩ or higher
      G158-3 (CNH1) - G158-4 (CNL1) Always 10 kΩ or higher

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G158-3 (CNH1) - Body ground Always Below 1 V
      G158-4 (CNL1) - Body ground Always Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT COMBINATION METER ASSEMBLY


    1. Remove the combination meter assembly.

      Click here

    2. A01QT7KN02

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      23 (MSCH) - 22 (MSCL) Always 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

  3. INSPECT NAVIGATION RECEIVER ASSEMBLY


    1. Remove the navigation receiver assembly.

      Click here

    2. A01QRVMN01

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

    OK

  4. CHECK COMBINATION METER ASSEMBLY


    1. Replace the combination meter assembly.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Check for DTCs.


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

    OK

  5. CHECK METER / GAUGE SYSTEM


    1. Turn the engine switch on (IG) and wait 30 seconds.

    2. Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

      OK
      Audio system returns to normal.
      Result
      Proceed to
      OK
      NG

    OK

    END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here