VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1422

DTC Code DTC Name
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction

DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more while the vehicle is being driven at a speed of 3 km/h (2 mph) or more.

  • STOP fuse

  • Stop light switch assembly

  • Wire harness or connector

  • Skid control ECU (Brake actuator assembly)

  • Brake actuator assembly (Master cylinder pressure sensor)

WIRING DIAGRAM

Refer to DTC C1425.

Click here

CAUTION / NOTICE / HINT

Note


  • When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    2. Turn the ignition switch off.

    3. Start the engine.

    4. Perform a road test.

    5. Check for DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Proceed to
      DTC C1422 is output
      DTCs C1422 and C1380 are output
      DTCs C1422 and C1425 are output

    DTCs C1422 and C1380 are output

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    DTCs C1422 and C1425 are output

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    DTC C1422 is output

  2. READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    5. In accordance with the display on the GTS, read the Data List.


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch assembly ON or OFF

      OFF: Brake pedal released

      ON: Brake pedal depressed

      		 -

      Chassis > ABS/VSC/TRC > Data List
      Tester Display
      Stop Light SW

    6. Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

      OK
      The GTS displays ON or OFF according to brake pedal operation.
      Result
      Proceed to
      OK
      NG

    NG

    CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION Click here

    OK

  3. READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    5. In accordance with the display on the GTS, read the Data List.


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Master Cylinder Pressure Master cylinder pressure sensor pressure

      Min.: 0.00 MPa

      Max.: 23.28 MPa

      Brake pedal operated: Proportional to pedal force

      Brake pedal released: 0.00 to 1.76 MPa

      		 -

      Chassis > ABS/VSC/TRC > Data List
      Tester Display
      Master Cylinder Pressure
      OK
      Data List pressure is within standard range.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    OK

  4. RECONFIRM DTC


    1. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRAC > Clear DTCs

    2. Turn the ignition switch off.

    3. Start the engine.

    4. Perform a road test.

    5. Check if the same DTC is recorded.

      Click here


      Chassis > ABS/VSC/TRAC > Trouble Codes
      Result
      Proceed to
      DTC C1422 is not output
      DTC C1422 is output

    DTC C1422 is not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC C1422 is output

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  5. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION


    1. Turn the ignition switch off.

    2. Check the brake pedal height and stop light switch assembly installation.

      Click here

      OK
      The brake pedal height and stop light switch assembly installation are normal.
      Result
      Proceed to
      OK
      NG

    NG

    ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH Click here

    OK

  6. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Remove the stop light switch assembly.

      Click here

    2. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A01V7CNC84
      *a

      Front view of wire harness connector

      (to Skid Control ECU [Brake Actuator Assembly])

      Turn the ignition switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the A100 skid control ECU (brake actuator assembly) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A100-35 (STP) - Body ground Brake pedal depressed 8 to 14 V
      Brake pedal released Below 1.5 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR