FORWARD RECOGNITION CAMERA SYSTEM, Diagnostic DTC:C1AA3

DTC Code DTC Name
C1AA3 Vehicle Speed Sensor Circuit

DESCRIPTION

The forward recognition camera receives vehicle speed signals from the skid control ECU (brake actuator assembly). If the skid control ECU (brake actuator assembly) receives a vehicle speed sensor malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA3 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA3 Vehicle Speed Sensor Circuit 2 seconds after the ignition switch is turned ON, a signal indicating a malfunction in the vehicle speed sensor is received from the skid control ECU (brake actuator assembly) for 5 seconds or more.

  • Vehicle stability control system

  • Skid control ECU (Brake actuator assembly)

  • Forward recognition camera

CAUTION / NOTICE / HINT

Note


  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

  • If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

    Click here

  • First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

    Click here

PROCEDURE


  1. CHECK DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

    5. Check if DTCs are output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      Vehicle stability control system DTCs are not output. A
      Vehicle stability control system DTCs are output. B

    B

    GO TO VEHICLE STABILITY CONTROL SYSTEM Click here

    A

  2. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.

    5. Clear the DTCs.

      Click here


      Chassis > Front Recognition Camera > Clear DTCs

    6. Make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the system cannot detect the malfunction.


      1. Wait 7 seconds or more after turning the ignition switch to ON.

    7. Check for DTCs.

      Click here


      Chassis > Front Recognition Camera > Trouble Codes
      Result
      Result Proceed to
      DTC C1AA3 is output A
      DTC C1AA3 is not output B

    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  3. REPLACE FORWARD RECOGNITION CAMERA


    1. Replace the forward recognition camera.

      Click here

    2. Adjust the forward recognition camera.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.

    5. Clear the DTCs.

      Click here


      Chassis > Front Recognition Camera > Clear DTCs

    6. Make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the system cannot detect the malfunction.


      1. Wait 7 seconds or more after turning the ignition switch to ON.

    7. Check for DTCs.

      Click here


      Chassis > Front Recognition Camera > Trouble Codes
      Result
      Result Proceed to
      DTC C1AA3 is output A
      DTC C1AA3 is not output B

    A

    REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) Click here

    B

    END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)