ECD SYSTEM, Diagnostic DTC:P245B

DTC Code DTC Name
P245B Exhaust Gas Recirculation Cooler Bypass Control Circuit Range / Performance Bank 1

DESCRIPTION

Refer to DTC P245A.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P245B Exhaust Gas Recirculation Cooler Bypass Control Circuit Range / Performance Bank 1

EGR cooler bypass switching valve assembly circuit over temperature for 0.05 seconds.

(3 trip detection logic)

  • EGR cooler bypass switching valve assembly

  • Open or short in EGR cooler bypass switching valve assembly circuit

  • Cooling fan system

  • ECM

 Does not come on DTC stored

WIRING DIAGRAM

Refer to DTC P245A.

Click here

CAUTION / NOTICE / HINT

Note

When replacing the ECM, the ECM needs registration and initialization.

Click here

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF FAN HIGH SPEED AND LOW SPEED)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan High Speed and Actuator Test of Fan Low Speed.


      Powertrain > Engine and ECT > Active Test
      Tester Display
      Actuator Test of Fan High Speed

      Powertrain > Engine and ECT > Active Test
      Tester Display
      Actuator Test of Fan Low Speed
      OK
      Cooling fan operates according to operation.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE COOLING FAN SYSTEM Click here

    OK

  2. INSPECT EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY


    1. Inspect the EGR cooler bypass switching valve assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - ECM)


    1. Disconnect the EGR cooler bypass switching valve assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B109-2 (ECBV) - B112-16 (ECBV) Always Below 1 Ω
      B109-2 (ECBV) or B112-16 (ECBV) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 9 Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

    A01QSRXC04
    *a

    Front view of wire harness connector

    (to EGR Cooler Bypass Switching Valve Assembly)

    1. Disconnect the EGR cooler bypass switching valve assembly connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B109-1 (+B) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY) Click here

    OK

  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


      Powertrain > Engine and ECT > Trouble Codes

    8. Confirm that the DTC is not output again.

      Result
      Proceed to
      NEXT

    NEXT

    END

  7. CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)


    1. Disconnect the EGR cooler bypass switching valve assembly connector.

    2. Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B109-1 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
      B109-1 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  8. CHECK ECM POWER SOURCE CIRCUIT


    1. Check the ECM power source circuit.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 6 Click here

  9. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 6 Click here

  10. REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY


    1. Replace the EGR cooler bypass switching valve assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 6 Click here

  11. REPAIR OR REPLACE COOLING FAN SYSTEM


    1. Repair or replace the cooling fan system.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 6 Click here