CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE NO. 2 CYLINDER HEAD COVER

    Click here

  4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  5. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  6. REMOVE BATTERY CLAMP SUB-ASSEMBLY

    Click here

  7. REMOVE BATTERY

  8. REMOVE BATTERY TRAY

  9. DISCONNECT ENGINE WIRE


    1. Detach the 9 clamps, and then disconnect the connectors.

    2. Remove the 3 bolts and 2 nuts, and then disconnect the engine wire.

      B0029E8

  10. REMOVE IGNITION COIL ASSEMBLY


    1. B002AAI

      Remove the 4 bolts and 4 ignition coil assemblies.

  11. REMOVE AIR TUBE


    1. B0029RWC01
      *1 Fuel Vapor Feed Hose
      *2 Union to Connector Tube Hose
      *3 No. 2 Air Hose
      *4 No. 1 Fuel Vapor Feed Hose

      Slide the clamp and disconnect the fuel vapor feed hose from the purge VSV.

    2. Slide the 2 clamps and disconnect the 2 union to connector tube hoses.

    3. Disconnect the No. 2 air hose and No. 1 fuel vapor feed hose.

    4. Remove the 2 bolts and air tube.

  12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

    Click here

  13. REMOVE CYLINDER HEAD COVER GASKET

    Click here

  14. REMOVE CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY


    1. B00297GC02
      *a No. 3 Cylinder
      *b No. 1 Cylinder

      Rotate the crankshaft clockwise until the intake camshaft position at the No. 1 cylinder and No. 3 cylinder are as shown in the illustration.

      Tech Tips

      If the intake camshaft position is not as shown in the illustration, rotate the intake crankshaft clockwise again so that the camshaft is aligned as shown in the illustration.

    2. Turn the crankshaft counterclockwise approximately 10 to 15°.

    3. B002ACE

      Using a screwdriver, slide the valve lift control actuator connector clip from the valve lift control actuator connector.

      Note

      Slide only the upper part of the valve lift control actuator connector clip, as the straight pin will falls out from the bottom if the valve lift control actuator connector clip is completely removed.

    4. B002ALM

      Using 2 screwdrivers, lightly pry the valve lift control actuator connector to make a space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly.

      Note


      • Do not forcefully pry the valve lift control actuator connector.

      • Do not damage the camshaft housing sub-assembly and camshaft bearing cap.

    5. B002AMS

      Using a magnet hand, remove the straight pin from the valve lift control actuator connector.

      Note

      Do not drop the straight pin into the engine.

      Tech Tips


      • The straight pin can be removed by utilizing the space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly to move the continuously variable valve lift controller assembly so that there is no load on the straight pin.

      • If the straight pin cannot removed easily, slightly turn the crankshaft clockwise and then counter clockwise.

    6. B0029FQ

      Using a screwdriver, remove the valve lift control actuator connector clip from the valve lift control actuator connector.

      Note

      Do not drop the valve lift control actuator connector clip into the engine.

    7. B002A6Y

      Remove the bolt, 2 nuts and wire harness clamp bracket from the continuously variable valve liftcontroller assembly.

    8. B002A5E

      Remove the continuously variable valve lift controller assembly from the camshaft housing sub-assembly.

    9. B0029XQC01
      *1 O-Ring

      Remove the O-ring from the continuously variable valve lift controller assembly.

    10. B002AIP

      Remove the valve lift control actuator connector from the valve rocker shaft.