ECD SYSTEM(for CCo), Diagnostic DTC:P0724

DTC Code DTC Name
P0724 Brake Switch "B" Circuit High

DESCRIPTION

This DTC indicates that the stop light switch assembly remains ON. When the stop light switch assembly remains ON during GO and STOP driving, the ECM interprets this as a fault in the stop light switch assembly. Then the MIL illuminates and the ECM stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Brake Switch "B" Circuit High

Stop light switch assembly remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times.

(2 trip detection logic)

  • Short in stop light switch assembly signal circuit

  • Stop light switch assembly

  • ECM

 Comes on DTC stored
Related Data List
DTC No. Data List
P0724 Stop Light Switch

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0724 Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times.

WIRING DIAGRAM

Refer to DTC P0504 Click here.

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration (Click here ) and initialization Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (STOP LIGHT SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.


      Powertrain > Engine > Data List
      Tester Display
      Stop Light Switch

    5. Read the value displayed on the tester when the brake pedal is depressed and released.

      OK
      Brake Pedal Display
      Released OFF
      Depressed ON
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 6 Click here

    NG

  2. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  3. CHECK TERMINAL VOLTAGE (STP VOLTAGE)


    1. A00YUGCC05
      *a Brake Pedal Depressed
      *b Brake Pedal Released
      *c

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Brake Pedal Condition Specified Condition
      A61-35 (STP) - Body ground Released Below 1.5 V
      Depressed 7.5 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  4. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 6 Click here

  5. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT

    NEXT

  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off for 30 seconds or more.

    6. Turn the ignition switch to ON and turn the GTS on.

    7. Start the engine.

    8. Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times or more.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


      Powertrain > Engine > Trouble Codes

    10. Confirm that the DTC is not output again.

      Tech Tips

      Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


      1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


        Powertrain > Engine > Utility
        Tester Display
        All Readiness

      2. Input DTC P0724.

      3. Check that STATUS is NORMAL.

        Tech Tips


        • If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.

        • If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Perform the following procedure again 5 times: accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less.

      Result
      Proceed to
      NEXT

    NEXT

    END

  7. REPLACE STOP LIGHT SWITCH ASSEMBLY


    1. Replace the stop light switch assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 6 Click here