СИСТЕМА ECD (для моделей с контроллером свечей накаливания), Diagnostic DTC:P0182, P0183

DTC Code DTC Name
P0182 Fuel Temperature Sensor "A" Circuit Low Input
P0183 Fuel Temperature Sensor "A" Circuit High Input

DESCRIPTION

B00426XE02
Fig. 1
*1 Resistance Ω
*2 Acceptable
*3 Temperature °C (°F)

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low.

The variations of resistance are communicated to the ECM as changes in voltage (See Fig. 1).

The fuel temperature sensor is powered by a 5 V supply from the THF terminal of the ECM, register R.

Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change of fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the supply pump assembly and determines if there are malfunctions.

Tech Tips

When the fuel temperature sensor output is outside the normal range, the ECM determines that there is a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0182 Fuel Temperature Sensor "A" Circuit Low Input

Open or short in fuel temperature sensor circuit for 2.0 seconds

(2 trip detection logic)

  • Open or short in fuel temperature sensor circuit

  • Fuel temperature sensor

  • ECM

 Comes on DTC stored
P0183 Fuel Temperature Sensor "A" Circuit High Input

Open or short in fuel temperature sensor circuit for 2.0 seconds

(2 trip detection logic)

  • Open or short in fuel temperature sensor circuit

  • Fuel temperature sensor

  • ECM

 Comes on DTC stored
DTC Detection Drive Pattern
DTC No. DTC Detection Drive Pattern
P0182 Ignition switch ON for approximately 15 seconds
P0183
Related Data List
DTC No. Data List
P0182 Fuel Temperature
P0183

Tech Tips

When DTC P0182 or P0183 is stored, check the fuel temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit

WIRING DIAGRAM

B0043L0E09
*a Fuel Temperature Sensor

CAUTION / NOTICE / HINT

Note

When replacing the ECM, perform ECM Initialization and Registration.

Click here

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (FUEL TEMPERATURE)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


      Powertrain > Engine and ECT > Data List
      Tester Display
      Fuel Temperature

    4. Read the value.

      OK
      Same as actual fuel temperature.
      Result
      Result Proceed to
      -40°C (-40°F) A
      150°C (302°F) or higher B
      Same as actual fuel temperature C

      Tech Tips


      • If there is an open circuit, the GTS indicates -40°C (-40°F).

      • If there is a short circuit, the GTS indicates 150°C (302°F) or higher.


    B

    READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS) Click here

    C

    GO TO STEP 12 Click here

    A

  2. READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

    B00441NC02
    *1 Fuel Temperature Sensor
    *2 ECM
    *a

    Front view of wire harness connector

    (to Fuel Temperature Sensor)

    1. Disconnect the fuel temperature sensor connector.

    2. Connect terminals B122-1 and B122-2 of the fuel temperature sensor connector on the wire harness side.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON and turn the GTS on.

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


      Powertrain > Engine and ECT > Data List
      Tester Display
      Fuel Temperature

    6. Read the value.

      Standard
      150°C (302°F) or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM) Click here

    OK

  3. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE FUEL TEMPERATURE SENSOR


    1. Replace the fuel temperature sensor.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 8 Click here

  4. CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)


    1. Disconnect the fuel temperature sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B122-1 - B212-101 (THF) Always Below 1 Ω
      B122-2 - B212-133 (ETHF) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 11 Click here

    OK

  5. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 12 Click here

  6. READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

    B0044PYC14
    *1 Fuel Temperature Sensor
    *2 ECM

    1. Disconnect the fuel temperature sensor connector.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.


      Powertrain > Engine and ECT > Data List
      Tester Display
      Fuel Temperature

    5. Read the value.

      Standard
      -40°C (-40°F)
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM) Click here

    OK

  7. REPLACE FUEL TEMPERATURE SENSOR


    1. Replace the fuel temperature sensor.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  8. BLEED AIR FROM FUEL SYSTEM


    1. Bleed the air from the fuel system.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 12 Click here

  9. CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)


    1. Disconnect the fuel temperature sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B122-1 or B212-101 (THF) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  10. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 12 Click here

  11. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT

    NEXT

  12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON and wait for 15 seconds or more.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    7. Confirm that the pending DTC is not output again.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

    END