REAR DOOR (for TMC, TMMR Made) REASSEMBLY

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. REPAIR INSTRUCTION


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

        Heating Temperature
        Item Temperature
        Vehicle Body 40 to 60°C (104 to 140°F)

        Note

        Do not heat the vehicle body excessively.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Installation temperature


      1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

        Tech Tips


        • The most appropriate temperature for installing the tape is 25°C (77°F).

        • When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape elasticity increases.

    3. Before installation


      1. Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

        Tech Tips

        Spray water on the shop floor to settle any dust.

    4. Key points for handling the tape


      1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

        Note

        Do not bend the tape or leave it in high temperature places.

    5. Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

      Note


      • Position the tape accurately to achieve a neat finish and to avoid peeling.

      • The tape cannot be reused because it deforms and will not fit any more after being removed.


      1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.

        B000H3LE02
        Text in Illustration
        *A Pressing Forward *B Pulling
        *1 Non-padded Side *2 Padded Side
        *3 Squeegee *4 Black Out Tape
        *5 Release Paper - -
        *a Side View - -
        Reference Measurement
        Area Measurement
        A 10 to 20 mm (0.393 to 0.787 in.)
        B 30 to 70 mm/sec. (1.18 to 2.76 in./sec.)
        C 40 to 50° (for pressing forward)
        D 30 to 45° (for pulling)

        Note

        Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.

        Tech Tips


        • Either angle of the squeegee (pressing forward or pulling) is acceptable.

        • Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.

    6. Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)


      1. B000LZSE09
        Text in Illustration
        *1 Squeegee
        *2 Hem
        *a First
        *b Second
        *c Third

        If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

        Tech Tips

        When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

    7. Key points for installation of the tape (how to use a squeegee and installation procedure for corners)


      1. Remove the release paper and apply the tape carefully with your fingers.

      2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.

    8. Check after installation


      1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

        Note

        Do not reuse the tape.

  2. INSTALL REAR DOOR LOWER OUTSIDE STRIPE


    1. Refer to the illustration to position a new rear door lower outside stripe.

      B000HLCE02
      Text in Illustration
      *A LH Side *B RH Side
      *a Edge of Curved Surface *b Straight
      *c Triangle - -
      Standard Measurement
      Area Measurement Area Measurement
      A 1.5 mm (0.0591 in.) B 1.0 mm (0.0394 in.)

    2. Remove the release paper and apply the rear door lower outside stripe.

  3. INSTALL REAR DOOR OUTSIDE STRIPE


    1. Refer to the illustration to position a new rear door outside stripe.

      B000NRUE02
      Text in Illustration
      *A LH Side *B RH Side
      *a Edge of Curved Surface *b Straight
      *c Triangle - -
      Standard Measurement
      Area Measurement Area Measurement
      A 1.5 mm (0.0591 in.) B 1.0 mm (0.0394 in.)

    2. Remove the release paper and apply the rear door outside stripe.

  4. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING


    1. B000K98

      Engage the guide of the rear door upper window frame moulding to the door frame.

    2. Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 6 new rivets.

      Tech Tips

      If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

      Note


      • B000M8QE09

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

        Text in Illustration
        *1 Riveter
        *2 Mandrel
        *a Incorrect
      • B000LVPE10

        Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

        Text in Illustration
        *1 Riveter
        *a Incorrect
      • B000LUHE12

        Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.

        Text in Illustration
        *1 Riveter
        *a Incorrect

  5. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

    Tech Tips

    When installing a new rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body or rear door front window frame moulding excessively.


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

    2. B000J0OE01
      Text in Illustration
      *1 Double-sided Tape
      *2 Caulking Sponge

      Install a new rear door front window frame moulding.


      1. Using a heat light, heat the vehicle body and rear door front window frame moulding.

      2. Remove the release paper from the rear door front window frame moulding.

        Tech Tips

        After removing the release paper, keep the exposed adhesive free from foreign matter.

      3. Install the rear door front window frame moulding with the clip.

  6. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    1. B000I8S

      Engage the 6 claws to install the rear door belt moulding assembly as shown in the illustration.

  7. INSTALL REAR DOOR PANEL CUSHION


    1. B000MXR

      Engage the 2 claws to install 2 new rear door panel cushions.

  8. INSTALL REAR DOOR NO. 2 WEATHERSTRIP


    1. B000IZA

      Engage the 5 clips to install the rear door No. 2 weatherstrip.

  9. INSTALL CURTAIN HOOK (w/ Rear Door Sunshade)


    1. B000JQ3

      Engage the 2 claws and install the 2 curtain hooks.

    2. Engage the 2 pins as shown in the illustration.

  10. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.

    2. B000IG8E01
      Text in Illustration
      *1 Door Handle Nut
      *a Outside
      *b Inside

      Engage the claw.

    3. Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw and door handle nut.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

  11. INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD


    1. B000IYY

      Engage the 2 claws to install the rear door rear outside handle pad.

  12. INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. B000HOL

      Engage the 3 claws to install the rear door front outside handle pad.

  13. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. B000L5F

      Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

      Note

      If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.

    2. Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.

  14. INSTALL REAR DOOR OUTSIDE HANDLE COVER


    1. B000MLT

      Engage the claw and install the rear door outside handle cover.

    2. Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

  15. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. B000L4Q

      Install the rear door inside locking cable assembly.

    2. B000M7R

      Engage the 3 claws.

  16. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. B000IZC

      Install the rear door lock remote control cable assembly.

    2. B000I3T

      Engage the claw.

  17. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

    Note


    • When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door with motor lock assembly.


    1. Apply MP grease to the sliding parts of the rear door lock with motor assembly.

    2. When reusing the rear door with motor lock assembly:


      1. B000H1Z

        Install a new door lock wiring harness seal to the rear door lock with motor assembly.

    3. B000GYWE01
      Text in Illustration
      *1 Release Plate

      Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.

    4. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.

    5. Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  18. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

    Note

    The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


    1. B000H7L

      Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      When replacing the rear window regulator, a new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  19. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

    2. Install the temporary bolt to the rear door window regulator assembly.

    3. B000KAVE02
      Text in Illustration
      *1 Temporary Bolt

      Temporarily install the rear door window regulator assembly.

    4. Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  20. INSTALL REAR DOOR FRAME GARNISH


    1. B000LBE

      Engage the clip to install a new rear door frame garnish.

  21. INSTALL REAR DOOR GLASS CHANNEL FILLER


    1. Apply soapy water to a new rear door glass channel filler.

    2. B000LZVE01
      Text in Illustration
      *A Front Side
      *B Rear Side
      *a 4.57 mm (0.180 in.)
      *b 4.8 mm (0.189 in.)
      *c Edge of curved surface

      Install the rear door glass channel filler to the position shown in the illustration.

  22. INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY


    1. Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.

    2. B000J4ME01
      Text in Illustration
      *A Front Side
      *B Rear Side
      *a 4.57 mm (0.180 in.)
      *b 4.8 mm (0.189 in.)
      *c Edge of curved surface

      Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.

      Note

      To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.

  23. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. B000K9Q

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  24. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. B000NBK

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  25. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. B000MZL

      Install the rear door lower window frame sub-assembly with the screw and 2 bolts.

  26. INSTALL REAR DOOR GLASS RUN


    1. B000MBM

      Install the rear door glass run.

  27. INSTALL REAR DOOR WEATHERSTRIP


    1. B000L9C

      Engage the 20 clips to install the rear door weatherstrip.

  28. INSTALL REAR DOOR CHECK ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door check assembly.

    2. Apply adhesive to the threads of the bolt.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    3. B000JM1

      Install the rear door check assembly with the 2 nuts and bolt.

      Torque:
      Bolt
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }
      Nut
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  29. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the rear door panel.

    2. B000IIJE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  30. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. B000K30

      Install the rear door inner glass weatherstrip.

  31. INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)


    1. B000I83

      Install the rear curtain sub-assembly with the 9 screws.

  32. INSTALL REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY


    1. Engage the claw and 3 clamps, and install the rear door inside handle illumination light assembly.

  33. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. B000J2V

      Engage the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.

  34. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. B000H70

      Install the No. 1 door scuff plate clamp as shown in the illustration.

    2. B000K11E01
      Text in Illustration
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. Connect the connector.

    4. B000J14E01
      Text in Illustration
      *1 Reference Boss

      Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

    5. B000I2D

      Engage the 8 clips and install the rear door trim board sub-assembly.

    6. Install the 3 screws.

    7. If protective tape has been applied, remove it.

  35. INSTALL REAR ARMREST ASSEMBLY


    1. B000KAY

      Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.

  36. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. w/o Seat Heater System:


      1. Connect the connector.

    2. w/ Seat Heater System:


      1. Connect the 2 connectors.

    3. B000H23

      Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

  37. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. B000K01

      Engage the 3 claws to install the rear door inside handle bezel plug.

  38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Click here

  39. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  40. INSPECT POWER WINDOW OPERATION

    Click here