FRONT DOOR POWER WINDOW REGULATOR MOTOR (for TMC, TMMR Made) INSTALLATION

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

    Note

    The regulator arm must be below the intermediate position when installing the power window regulator motor.


    1. B000ICI

      Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  3. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. Apply MP grease to the sliding parts of the front door window regulator assembly.

    2. Install the temporary bolt to the front door window regulator assembly.

    3. B000ITZE02
      Text in Illustration
      *1 Temporary Bolt

      Temporarily install the front door window regulator assembly.

    4. Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. Disconnect the multiplex network master switch assembly.

    5. B000LNYE01

      Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.

    6. B000HBB

      Install the front door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    7. B000LXE

      Install the grommet.

  5. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the front door panel.

    2. B000MIAE01
      Text in Illustration
      *1 Reference Point

      Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

    3. Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

    4. Engage the 4 clamps.

    5. Connect each connector.

  6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    1. B000MP8

      Install the front door inner glass weatherstrip.

  7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. B000KO6E01
      Text in Illustration
      *1 Front Door Inside Locking Cable Assembly
      *2 Front Door Lock Remote Control Cable Assembly

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

    2. w/o Memory:


      1. Connect the connector.

    3. w/ Memory:


      1. Connect the 2 connectors.

    4. B000KHDE01
      Text in Illustration
      *1 Reference Boss

      Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

    5. B000NJZ

      Engage the 10 clips and install the front door trim board sub-assembly.

    6. Install the 3 screws.

    7. If protective tape has been applied, remove it.

  8. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. B000I67E01
      Text in Illustration
      *A for LH Side
      *B for RH Side

      Engage the claw to install the courtesy light assembly.

  9. INSTALL FRONT ARMREST ASSEMBLY


    1. B000LDC

      Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.

  10. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. Connect each connector.

    2. B000IAE

      Engage the 4 guides, 2 clips and 5 claws, and install the multiplex network master switch assembly with front door armrest base panel.

  11. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. Connect the connector.

    2. B000MFS

      Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.

  12. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. B000LAY

      Engage the 3 clips to install the front door lower frame bracket garnish.

  13. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. B000HXN

      Engage the 3 claws to install the front door inside handle bezel plug.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  16. INSPECT POWER WINDOW OPERATION

    Click here