FRONT DOOR POWER WINDOW REGULATOR MOTOR (for TMC, TMMR Made) REMOVAL

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. B000H8O

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

  4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. B000LAY

      Disengage the 3 clips and remove the front door lower frame bracket garnish.

  5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. B000MRM

      Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

    2. Disconnect each connector and remove the multiplex network master switch assembly with front door armrest base panel.

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. B000HBZ

      Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  7. REMOVE FRONT ARMREST ASSEMBLY


    1. B000N26

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.

  8. REMOVE COURTESY LIGHT ASSEMBLY


    1. B000NPFE01
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. B000LS6E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door panel.

    2. B000NJZ

      Remove the 3 screws.

    3. Using a clip remover, disengage the 10 clips.

    4. B000NQ1E01
      Text in Illustration
      *1 Reference Boss
      *2 Front Door Inner Glass Weatherstrip

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the front door panel.

    6. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    7. w/o Memory:


      1. Disconnect the connector.

    8. w/ Memory:


      1. Disconnect the 2 connectors.

    9. B000IDX

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. B000L90E01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  11. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. B000M0M

      Disconnect each connector.

    2. Disengage the 4 clamps.

    3. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. B000LXE

      Remove the grommet.

    2. Connect the cable to the negative (-) battery terminal.

    3. Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Disconnect the multiplex network master switch assembly.

    6. B000HBB

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    7. B000M3GE01

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  13. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. B000ITZE01
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    2. Remove the 5 bolts.

    3. Remove the front door window regulator assembly.

    4. Remove the temporary bolt from the front door window regulator assembly.

  14. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. B000ICI

      Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.