FRONT DOOR POWER WINDOW REGULATOR MOTOR (for TMMK Made) REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. B000JHU

      Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel plug as shown in the illustration.

  4. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER


    1. B000JC8

      Disengage the 2 claws and 2 guides to remove the front door front lower frame upper cover.

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. B000MJ9

      Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides.

    2. Disconnect each connector to remove the power window regulator master switch assembly with front door armrest base panel.

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. B000IX3

      Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides.

    2. Disconnect each connector to remove the power window regulator switch assembly with front door armrest base panel.

  7. REMOVE FRONT ARMREST ASSEMBLY


    1. B000N26

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the front armrest assembly.

  8. REMOVE COURTESY LIGHT ASSEMBLY


    1. B000NPFE01
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. B000KMQE01
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the front door panel.

    2. B000LET

      Remove the 3 screws.

    3. Using a clip remover, disengage the 10 clips.

    4. B000LEFE01
      Text in Illustration
      *1 Front Door Inner Glass Weatherstrip
      *a Reference Boss

      Pull out the front door trim board sub-assembly as shown in the illustration.

    5. Disengage the reference boss from the front door panel.

    6. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    7. B000M72

      Disengage the clamp.

    8. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly as shown in the illustration.

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. B000H3BE01
      Text in Illustration
      *a Screwdriver

      Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  11. REMOVE DOOR SIDE AIRBAG SENSOR


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Disconnect the connector from the door side airbag sensor.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        B000H9EE12
        Text in Illustration
        *1 White Housing Lock *2 Yellow CPA
        *a Connector Lock is Released - -

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting.

    4. B000KCV

      Remove the bolt and door side airbag sensor from the front door panel.

      Note

      Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    5. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      B000MUCE01
      Text in Illustration
      *a Incorrect *b Correct

  12. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. B000K3E

      Remove the bolt.

    2. Disconnect each connector.

    3. Disengage the 5 clamps.

    4. Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through the front door service hole cover.

    5. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the front door panel.

  13. REMOVE NO. 1 FRONT DOOR SERVICE HOLE SEAL


    1. B000M0G

      Remove the No. 1 front door service hole seal.

  14. REMOVE NO. 2 FRONT DOOR SERVICE HOLE SEAL


    1. B000ITI

      Remove the No. 2 front door service hole seal.

  15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. B000IXO

      Remove the grommet.

    2. Connect the cable to the negative (-) battery terminal.

    3. for Driver Side:


      1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

      2. Disconnect the power window regulator master switch assembly.

    4. for Front Passenger Side:


      1. Connect the power window regulator switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

      2. Disconnect the power window regulator switch assembly.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    6. B000KMS

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the front door glass sub-assembly to fall.

    7. B000KWWE02

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the front door glass sub-assembly.

  16. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. B000M1NE03
      Text in Illustration
      *a Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.

    2. Remove the 5 bolts.

    3. Remove the front door window regulator assembly.

    4. Remove the temporary bolt from the front door window regulator assembly.

  17. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. B000NAJ

      Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.