ROOF HEADLINING (for TMC, TMMR Made) INSTALLATION


  1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. B000NRGE01
      Text in Illustration
      *1 Clip (Black)
      *2 Clip (White)

      Install the 2 clips to the roof headlining assembly.

    2. B000J70

      Put the roof headlining assembly into the vehicle through the front door RH.

      Note

      Do not damage the roof headlining assembly or body interior.

    3. Engage the 2 clips.

      B000M2Y
    4. Install the roof headlining assembly with the 2 clips.

    5. Engage the 4 clamps to the front pillar LH.

    6. Engage the 3 clamps to the front pillar RH.

    7. Connect the bracket with the bolt to the front pillar RH.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
    8. Engage the 2 clamps and connect the connector to the rear pillar RH.

    9. w/ Television Antenna:


      1. Connect the connector.

    10. w/ Rain Sensor:


      1. Connect the connector.

    11. w/ EC Mirror:


      1. Connect the connector.

  2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. B000NRGE01
      Text in Illustration
      *1 Clip (Black)
      *2 Clip (White)

      Install the 2 clips to the roof headlining assembly.

    2. B000IX7

      Put the roof headlining assembly into the vehicle through the front door RH.

      Note

      Do not damage the roof headlining assembly or body interior.

    3. Engage the 2 clips and 2 fasteners.

      B000IX8
    4. Install the roof headlining assembly with the 2 clips.

    5. Engage the 4 clamps to the front pillar LH.

    6. Engage the 3 clamps to the front pillar RH.

    7. Connect the bracket with the bolt to the front pillar RH.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
    8. Engage the 2 clamps and connect the connector to the rear pillar RH.

    9. Connect the connector to the sliding roof drive gear assembly.

    10. w/ Television Antenna:


      1. Connect the connector.

    11. w/ Rain Sensor:


      1. Connect the connector.

    12. w/ EC Mirror:


      1. Connect the connector.

  3. INSTALL VISOR HOLDER


    1. B000ILM

      Engage the 2 claws.

    2. Push in the visor holder as shown in the illustration.

      Tech Tips

      Use the same procedure for the other visor holder.

  4. INSTALL VISOR ASSEMBLY LH


    1. Install the visor assembly LH with the 2 screws.

  5. INSTALL VISOR BRACKET COVER (for LH Side)


    1. B000IGN

      Engage the 4 claws to install the visor bracket cover.

  6. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. INSTALL VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  8. INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    1. B000H1PE02
      Text in Illustration
      *1 Notch
      *2 Alignment Mark
      *3 Tape

      Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.

      Note

      After installation, check that the corners fit correctly.

      Tech Tips

      Make sure that the tape is positioned as shown in the illustration.

  9. INSTALL ASSIST GRIP SUB-ASSEMBLY


    1. B000IQX

      Put an assist grip sub-assembly together as shown in the illustration.

    2. B000KBK

      Engage the 2 clips to install the assist grip sub-assembly.

    3. B000KGV

      Engage the 4 claws to install the 2 assist grip covers

      Tech Tips

      Use the same procedure for the RH side.

  10. INSTALL REAR ASSIST GRIP ASSEMBLY LH


    1. B000J2S

      Put an rear assist grip assembly LH together as shown in the illustration.

    2. B000K3C

      Engage the 2 clips to install the rear assist grip assembly LH.

    3. B000HOG

      Engage the 4 claws to install the 2 assist grip covers

  11. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. INSTALL SPOT LIGHT ASSEMBLY


    1. Connect the connector.

    2. B000NQYE01
      Text in Illustration
      *a Front

      Engage the 4 claws to install the spot light assembly.

  13. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)


    1. Connect the connector.

    2. B000MBL

      Engage the 4 clips to install the roof console box assembly.

  14. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)


    1. Connect the connector.

    2. B000MII

      Engage the 4 clips to install the roof console box assembly.

  15. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)


    1. Engage the 2 claws to install the rain sensor cover.

  16. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. except TMMR Made:


      1. Engage the 6 claws and temporarily install the inner rear view mirror stay holder cover.

      2. B000K3L

        Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration and engage the 2 claws to install the cover.

    2. for TMMR Made:


      1. Engage the 2 claws to temporarily install the inner rear view mirror stay holder cover.

      2. B000LBR

        Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration to engage the 2 guides and install the cover.

  17. INSTALL INSTRUMENT PANEL SAFETY PAD

    Click here

  18. INSTALL FRONT SEAT ASSEMBLY LH

    for Manual Seat Click here

    for Power Seat Click here

  19. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  20. INSTALL ROOF SIDE INNER GARNISH LH


    1. Engage the guide.

    2. Engage the 5 clips to install the roof side inner garnish LH.

  21. INSTALL REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)


    1. Engage the guide, claw and 2 clips.

    2. Install the rear seat side garnish LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
  22. INSTALL CENTER PILLAR UPPER GARNISH LH


    1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.

    2. Engage the clip.

    3. Install the center pillar upper garnish LH with the 2 screws.

  23. INSTALL CENTER PILLAR LOWER GARNISH LH


    1. Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.

  24. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. Install the floor anchor of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. Check if the ELR locks.

      Note

      The check should be performed with the front seat outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  25. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)


    1. Engage the 3 claws to install the lap belt outer anchor cover.

  26. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. B000JVDE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  27. INSTALL REAR DOOR SCUFF PLATE LH


    1. Engage the 6 claws to install the rear door scuff plate LH.

      Tech Tips

      Engage the claws from the rear side of the scuff plate.

  28. INSTALL ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  29. INSTALL REAR SEAT SIDE GARNISH RH (for Reclining Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  30. INSTALL CENTER PILLAR UPPER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  31. INSTALL CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  32. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  33. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  34. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. B000KSGE01
      Text in Illustration
      *1 Alignment Mark (Blue)

      Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  35. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  36. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Place the rear side seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the hook to install the rear side seatback assembly LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    3. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide LH.

  37. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)


    1. Place the rear side seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the hook to install the rear side seatback assembly RH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    3. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide RH.

  38. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    1. B000HKU

      Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  39. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Engage the 2 clamps.

      2. Connect the connector.

    3. B000LR0

      Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  40. INSTALL REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Engage the clamp.

      2. Connect the connector.

    3. Install the rear seatback assembly LH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    4. B000I0G

      Engage the fastener as shown in the illustration.

    5. Raise the rear seatback assembly LH.

    6. Connect the rear seat outer belt assembly to the rear seat center shoulder belt guide.

  41. INSTALL REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)


    1. Place the rear seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Engage the clamp.

      2. Connect the connector.

    3. Install the rear seatback assembly RH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    4. B000JB7

      Engage the fastener as shown in the illustration.

    5. Raise the rear seatback assembly RH.

  42. INSTALL CENTER SEATBACK ASSEMBLY (for Reclining Seat Type)


    1. Place the center seatback assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the hook.

    3. Install the center seatback assembly with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    4. Connect the connector.

  43. INSTALL REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH with the 2 bolts and 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    3. Engage the 2 hooks to install the cover.

    4. Connect the 2 rear seat belts to the 2 rear seat shoulder belt guides.

    5. w/ Rear Seat Side Airbag:


      1. Connect each connector and clamp to the child restraint anchor bracket sub-assembly LH.

  44. INSTALL REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type)


    1. Place the rear seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly RH with the 2 bolts and 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    3. Engage the 2 hooks to install the cover.

    4. Connect the rear seat belt to the rear seat shoulder belt guide.

    5. w/ Rear Seat Side Airbag:


      1. Connect each connector and clamp to the child restraint anchor bracket sub-assembly RH.

  45. INSTALL REAR SEATBACK COVER (for Reclining Seat Type)


    1. Engage the 4 claws to install the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  46. INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    1. B000HKU

      Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  47. INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.

    3. Connect the 2 seat heater connectors.

    4. B000KYT

      Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.

    5. Confirm that the rear seat cushion assembly is securely installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  48. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

  49. INSTALL REAR SEAT HEADREST ASSEMBLY

  50. INSTALL FRONT PILLAR GARNISH LH


    1. Remove the protective cover.

    2. Make sure that the front pillar garnish clip is not damaged.

      Note

      If there is any damage, replace the garnish clip with a new one.

    3. B000M81

      Install the front pillar garnish clip to front pillar garnish LH.

      Tech Tips

      Install the front pillar garnish clip so that it faces as shown in the illustration.

      B000ITLE01
      Text in Illustration
      *a Correct *b Incorrect
    4. Engage the 2 guides as shown in the illustration.

    5. B000J51

      Engage the 2 clips to install the front pillar garnish LH.

  51. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. B000HY0E01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  52. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. Engage the 2 clips.

    2. Install the cowl side trim sub-assembly LH with the clip.

  53. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Engage the 10 claws to install the front door scuff plate LH.

  54. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  55. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. B000HULE01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  56. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  57. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  58. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  59. INSPECT SRS WARNING LIGHT

    Click here