INSTRUMENT PANEL SAFETY PAD (for TMC, TMMR Made) INSTALLATION


  1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. Engage the 5 guides and temporarily install the instrument panel safety pad assembly as shown in the illustration.

      B000JN3

      Note


      • Do not damage the instrument panel safety pad assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.

    2. Install the 2 clips.

    3. Install the 3 bolts <B> and nut <F> or <G>.

    4. Install the 2 passenger airbag bolts <A>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
    5. B000M39

      Install the glove box light as shown in the illustration.

    6. Engage each clamp.

    7. Connect each connector.

  2. CONNECT NO. 2 INSTRUMENT PANEL WIRE


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. B000L23

      Connect the connector.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

  3. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    1. B000MZ1

      Engage the 10 clips to install the No. 1 instrument panel garnish sub-assembly as shown in the illustration.

  4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. for LHD with Smart Entry and Start System:


      1. Connect the connector.

    2. Engage the 3 clips and guide to install the lower instrument panel finish panel assembly.

  5. INSTALL CONSOLE BOX INSERT


    1. B000LNO

      Engage the clip and 4 guides as shown in the illustration.

    2. Install the console box insert with the 2 screws <D>.

    3. for RHD:


      1. Engage the 2 claws to connect the room temperature sensor.

  6. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    1. B000I45

      Engage the clip and 4 guides as shown in the illustration.

    2. Install the front No. 2 console box insert with the 2 screws <D>.

    3. for LHD:


      1. Engage the 2 claws to connect the room temperature sensor.

  7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  8. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B000I4E

      Engage the 2 guides.

    2. Engage the 3 claws and 2 clips to install the No. 2 instrument panel speaker panel sub-assembly.

  9. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  10. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)


    1. Connect the connector.

    2. B000NPPE01

      Install the front No. 3 speaker assembly with the 2 screws.

      Note

      Do not touch the speaker cone.

      Tech Tips

      Install the screws in the order shown in the illustration.

  11. INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY


    1. Connect the connector.

    2. B000JEI

      Engage the 6 clips to install the No. 1 speaker opening cover assembly.

  12. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    1. Connect the connector.

    2. B000H46E01
      Text in Illustration
      *A LH Side
      *B RH Side

      Install the front No. 2 speaker assembly with the 2 screws.

      Note

      Do not touch the speaker cone.

      Tech Tips

      Install the screws in the order shown in the illustration.

  13. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B000LTX

      Engage the 2 guides.

    2. Engage the 3 claws and 2 clips to install the No. 1 instrument panel speaker panel sub-assembly.

  14. INSTALL FRONT PILLAR GARNISH LH


    1. Remove the protective cover.

    2. Make sure that the front pillar garnish clip is not damaged.

      Note

      If there is any damage, replace the garnish clip with a new one.

    3. B000M81

      Install the front pillar garnish clip to front pillar garnish LH.

      Tech Tips

      Install the front pillar garnish clip so that it faces as shown in the illustration.

      B000ITLE01
      Text in Illustration
      *a Correct *b Incorrect
    4. Engage the 2 guides as shown in the illustration.

    5. B000J51

      Engage the 2 clips to install the front pillar garnish LH.

  15. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B000K3J

      Engage the 10 clips to install the No. 3 instrument panel register assembly.

  16. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. B000M97

      Engage the 2 clips and 4 guides.

    2. Install the 3 screws <D>.

    3. Close the lower instrument panel door.

    4. Install the lower instrument panel sub-assembly with the bolt <B> and screws <D>.

  17. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.

  18. INSTALL INSTRUMENT SIDE PANEL RH


    1. B000KV2

      Engage the 3 guides as shown in the illustration.

    2. B000NEO

      Engage the 4 claws to install the instrument side panel RH as shown in the illustration.

  19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. B000HULE01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  21. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  22. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver)


    1. Connect the connector.

    2. Engage the 6 clips.

    3. Install the center instrument cluster finish panel with air conditioning control assembly with the 4 bolts <C>.

  23. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type)


    1. Connect each connector.

    2. Engage the 6 clips to the vehicle body to temporarily install the radio receiver assembly with air conditioning control assembly.

    3. Install the radio receiver assembly with air conditioning control assembly with the 4 bolts.

  24. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type)


    1. Connect each connector.

    2. Engage the 6 clips to the vehicle body to temporarily install the navigation receiver assembly with air conditioning control assembly.

    3. Install the navigation receiver assembly with air conditioning control assembly with the 4 bolts.

  25. INSTALL FRONT ASH RECEPTACLE ASSEMBLY


    1. Connect each connector.

    2. B000JWH

      Engage the 2 clips.

    3. Install the front ash receptacle assembly with the 2 screws <D>.

  26. INSTALL FRONT CONSOLE UPPER PANEL GARNISH


    1. for Blank Type:


      1. B000HOA

        Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.

    2. for 3 Switch Hole Type:


      1. Connect each connector.

      2. B000N2U

        Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.

  27. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Connect the connector.

    2. B000LVO

      Engage the 4 clips to install the No. 2 instrument panel register assembly.

      Note

      When installing the No. 2 instrument panel register assembly, check that the wire harness is not caught between the No. 2 instrument panel register assembly and duct.

  28. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. B000NS6

      Engage the 7 clips and 2 guides to install the center instrument cluster finish panel sub-assembly.

  29. INSTALL CONSOLE BOX ASSEMBLY


    1. B000J09

      Engage the 4 guides as shown in the illustration.

    2. Install the console box assembly with the 2 bolts and 2 screws.

  30. INSTALL CONSOLE BOX CARPET


    1. Install the console box carpet.

  31. INSTALL NO. 4 CONSOLE BOX DUCT


    1. Engage the claw to install the No. 4 console box duct.

  32. INSTALL UPPER CONSOLE BOX SUB-ASSEMBLY


    1. Connect the 2 connectors.

    2. Engage the clamp.

    3. B000MYF

      Engage the 2 guides and 4 clips as shown in the illustration.

    4. Install the upper console box sub-assembly with the 2 screws.

  33. INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. B000JVU

      Engage the 6 clips to install the rear console upper panel sub-assembly.

    3. Move the shift lever to P.

  34. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. B000IUA

      Turn the shift lever knob sub-assembly clockwise to install it.

    2. B000JBW

      Engage the 2 claws to connect the shift hole cover sub-assembly as shown in the illustration.

  35. INSTALL FRONT PANEL GARNISH RH


    1. B000KNC

      Engage the 3 clips and 8 guides to install the front panel garnish RH.

  36. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY


    1. w/o Driver Side Knee Airbag:


      1. Engage the 5 clips and 3 guides.

    2. w/ Driver Side Knee Airbag:


      1. Engage the 4 claws, 7 clips and 3 guides.

    3. Install the instrument panel sub-assembly with the 2 bolts <B>.

  37. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  38. INSTALL FRONT PANEL GARNISH LH


    1. B000N75

      Engage the 3 clips and 8 guides to install the front panel garnish LH.

  39. INSTALL COMBINATION METER ASSEMBLY


    1. Connect the 2 connectors.

    2. Engage the wire harness clamp.

    3. Install the combination meter assembly with the 4 screws.

  40. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. B000JQN

      Temporarily install the instrument cluster finish panel assembly as shown in the illustration.

    2. Connect each connector.

    3. for LHD:


      1. Engage the 3 claws, 7 clips and 4 guides.

    4. for RHD:


      1. Engage the 4 claws, 5 clips and 4 guides.

    5. B000NPS

      Engage the 4 clips and 2 guides to install the instrument cluster finish panel assembly.

  41. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B000IKO

      Engage the 4 clips to install the No. 1 instrument panel register assembly.

  42. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. w/ Smart Entry and Start System:


      1. Connect the connector.

    2. B000J2O

      Engage the 2 claws and 4 clips to install the upper instrument panel finish panel.

  43. INSTALL INSTRUMENT SIDE PANEL LH


    1. Engage the 3 guides.

    2. B000N7A

      Engage the 4 claws to install the instrument side panel LH as shown in the illustration.

  44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. B000HY0E01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  45. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. Engage the 2 clips.

    2. Install the cowl side trim sub-assembly LH with the clip.

  46. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Engage the 10 claws to install the front door scuff plate LH.

  47. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  48. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)

    Note


    • Reset the auto away/return function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  49. INSPECT SRS WARNING LIGHT

    Click here