AIRBAG SYSTEM (for TMMK Made) SRS Warning Light Remains ON

DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the engine switch is turned from off to on (IG), and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

B000IVSE08

INSPECTION PROCEDURE

Note


  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK SRS WARNING LIGHT OPERATION


    1. Turn the engine switch on (IG) and check the SRS warning light condition.

      Tech Tips

      The primary check is performed for approximately 6 seconds after the engine switch is turned on (IG).

      Result
      Result Proceed to
      After the primary check period, the SRS warning light remains on. A
      After the primary check period, the SRS warning light goes off and comes on again. B

    B

    CHECK CAN COMMUNICATION SYSTEM Click here

    A

  2. CHECK BATTERY VOLTAGE


    1. Measure the voltage of the battery.

      Standard Voltage
      11 to 14 V

    NG

    INSPECT CHARGING SYSTEM AND BATTERY Click here

    OK

  3. CHECK CONNECTOR


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the airbag sensor assembly.

      OK
      The connector is properly connected.

      Tech Tips

      If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the airbag sensor assembly.

    5. Check that the terminal of the connector is not damaged.

      OK
      The terminal is not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  4. CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)


    1. B000KUUE05
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I47-21 (IG2) - Body ground Engine switch on (IG) 8 to 16 V

    5. Turn the engine switch off.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I47-25 (E1) - Body ground Always Below 1 Ω
      I47-26 (E2) - Body ground Always Below 1 Ω

    NG

    REPLACE WIRE HARNESS

    OK

  5. CHECK SRS WARNING LIGHT


    1. Turn the engine switch on (IG) and check the SRS warning light condition.

      OK
      After the primary check period, the SRS warning light goes off for approximately 10 seconds and comes back on.

      Tech Tips

      The primary check period is approximately 6 seconds after the engine switch is turned on (IG).


    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  6. CHECK CAN COMMUNICATION SYSTEM


    1. Use the GTS to check if the CAN communication system is functioning normally.

      Tech Tips


      • Refer to Bus Check for the CAN communication system Click here.

      • The airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  7. CHECK BATTERY VOLTAGE


    1. Measure the voltage of the battery.

      Standard Voltage
      11 to 14 V

    NG

    INSPECT CHARGING SYSTEM AND BATTERY Click here

    OK

  8. CHECK CONNECTOR


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the airbag sensor assembly.

      OK
      The connector is properly connected.

      Tech Tips

      If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the airbag sensor assembly.

    5. Check that the terminal of the connector is not damaged.

      OK
      The terminal is not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  9. CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)


    1. B000KUUE05
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I47-21 (IG2) - Body ground Engine switch on (IG) 8 to 16 V

    5. Turn the engine switch off.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I47-25 (E1) - Body ground Always Below 1 Ω
      I47-26 (E2) - Body ground Always Below 1 Ω

    NG

    REPLACE WIRE HARNESS

    OK

  10. CHECK CONNECTOR


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Check that the connector is properly connected to the combination meter assembly.

      OK
      The connector is properly connected.

      Tech Tips

      If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

    3. Disconnect the connector from the combination meter assembly.

    4. Check that the terminal of the connector is not damaged.

      OK
      The terminal is not deformed or damaged.

    NG

    REPAIR OR REPLACE CONNECTOR

    OK

  11. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)


    1. B000K3AE09
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I18-13 (IG+) - Body ground Engine switch on (IG) 11 to 14 V
      I18-1 (B) - Body ground Always 11 to 14 V

    4. Turn the engine switch off.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I18-20 (ES) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE WIRE HARNESS

    OK

  12. CHECK SRS WARNING LIGHT


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Connect the connector to the combination meter assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the engine switch on (IG) and check the SRS warning light condition.

      OK
      After the primary check period, the SRS warning light goes off for approximately 10 seconds and comes back on.

      Tech Tips

      The primary check period is approximately 6 seconds after the engine switch is turned on (IG).


    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

    REPLACE AIRBAG SENSOR ASSEMBLY Click here