AIRBAG SYSTEM (for TMMK Made), Diagnostic DTC:B1627/82, B1628/82, B1637/82, B1638/82, B1647/82, B1697/82, B1698/82

DTC Code DTC Name
B1627/82 Lost communication with Side Airbag Sensor LH
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete
B1637/82 Lost Communication with Rear Airbag Sensor LH
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete
B1647/82 Lost Communication with Side Satellite Sensor Bus LH
B1697/82 Lost Communication with Door Side Airbag Sensor LH
B1698/82 Door Side Airbag Sensor LH Initialization Incomplete

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, rear seat airbag assembly LH, curtain shield airbag assembly LH and front seat outer belt assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH.

The side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected for the side collision sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area

B1627/82

B1628/82

B1637/82

B1638/82

B1647/82

B1697/82

B1698/82

  • The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit.

  • Side airbag sensor assembly LH malfunction

  • Side No. 2 airbag sensor assembly LH malfunction

  • Door side airbag sensor LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front door wire LH

  • Side airbag sensor assembly LH

  • Side No. 2 airbag sensor assembly LH

  • Door side airbag sensor LH

  • Airbag sensor assembly

WIRING DIAGRAM

B000LZZE34

INSPECTION PROCEDURE

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

PROCEDURE


  1. CHECK CURRENT DTC


    1. Check for current DTCs Click here.

      Result
      Result Proceed to
      Current DTC B1647 or 82 is output. A
      Current DTC B1628 or B1638 is output. B
      Current DTC B1697 or B1698 is output. C
      Current DTC B1627 or B1637 is output. D
      Current DTCs B1627, B1628, B1637, B1638, B1647, B1697, B1698 and 82 are not output. E

      Tech Tips


      • DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the engine switch off and then on (IG) again.

      • Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1697, B1698 and 82 may be output at this time, but they are not related to this check.


    B

    CHECK HISTORY DTC Click here

    C

    CHECK CONNECTORS Click here

    D

    CHECK CURRENT DTC Click here

    E

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. CHECK CONNECTORS


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  3. CHECK FLOOR WIRE (OPEN)


    1. B000MQOE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-4 (BBL+) -N8-3 (BBL-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.


    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK FLOOR WIRE (SHORT)


    1. B000MDBE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-4 (BBL+) - N8-3 (BBL-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  5. CHECK FLOOR WIRE (SHORT TO B+)


    1. B000MDBE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N8-4 (BBL+) - Body ground Engine switch on (IG) Below 1 V
      N8-3 (BBL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    REPLACE FLOOR WIRE

    OK

  6. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B000MDBE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-4 (BBL+) - Body ground Always 1 MΩ or higher
      N8-3 (BBL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  7. CHECK FLOOR WIRE (OPEN)


    1. B000NGZE22
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)
      *b

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)

      Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-1 (BCL+) - N8-2 (BCL-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.


    NG

    REPLACE FLOOR WIRE

    OK

  8. CHECK FLOOR WIRE (SHORT)

    B000HT3E04
    Text in Illustration
    *1 Side No. 2 Airbag Sensor Assembly LH
    *2 Side Airbag Sensor Assembly LH
    *3 Floor Wire
    *a

    Front view of wire harness connector

    (to Side Airbag Sensor Assembly LH)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-1 (BCL+) - N8-2 (BCL-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  9. CHECK FLOOR WIRE (SHORT TO B+)


    1. B000HT3E04
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N8-1 (BCL+) - Body ground Engine switch on (IG) Below 1 V
      N8-2 (BCL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    REPLACE FLOOR WIRE

    OK

  10. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B000HT3E04
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-1 (BCL+) - Body ground Always 1 MΩ or higher
      N8-2 (BCL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  11. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (OPEN)


    1. B000KT7E17
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Connect the connectors that link the floor wire and front door wire LH.

    2. Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N44-1 (BDL+) - N44-2 (BDL-) Always Below 1 Ω

    NG

    CHECK FRONT DOOR WIRE LH (OPEN) Click here

    OK

  12. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT)


    1. B000N5SE17
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)

      Disconnect the service wire from connector E.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N44-1 (BDL+) - N44-2 (BDL-) Always 1 MΩ or higher

    NG

    CHECK FRONT DOOR WIRE LH (SHORT) Click here

    OK

  13. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)


    1. B000N5SE17
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N44-1 (BDL+) - Body ground Engine switch on (IG) Below 1 V
      N44-2 (BDL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    CHECK FRONT DOOR WIRE LH (SHORT TO B+) Click here

    OK

  14. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)


    1. B000N5SE17
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N44-1 (BDL+) - Body ground Always 1 MΩ or higher
      N44-2 (BDL-) - Body ground Always 1 MΩ or higher

    NG

    CHECK FRONT DOOR WIRE LH (SHORT TO GROUND) Click here

    OK

  15. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B000IKTE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly

      Connect the connectors to the side No. 2 airbag sensor assembly LH, door side airbag sensor LH and airbag sensor assembly.

    2. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1647 or 82 is output. A
      DTC B1642 or 81 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  16. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH


    1. B000HY9E01
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly LH

      Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the engine switch off.

    5. Turn the engine switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1647 or 82 is output. A
      DTC B1642 or 81 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    7. Turn the engine switch off.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    9. Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  17. CHECK DOOR SIDE AIRBAG SENSOR LH


    1. B000IIWE01
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly LH

      Interchange the door side airbag sensor LH with RH and connect the connectors.

    2. Connect the cable to the negative (-) battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the engine switch off.

    5. Turn the engine switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1647 or 82 is output. A
      DTC B1642 or 81 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    7. Turn the engine switch off.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    9. Return the door side airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  18. CHECK HISTORY DTC


    1. Check for history DTCs Click here.

      Result
      Result Proceed to
      History DTCs B1627 and B1637 are not output. A
      History DTC B1627 is output. B
      History DTC B1637 is output. C

      Tech Tips

      Codes other than history DTCs B1627 and B1637 may be output at this time, but they are not related to this check.


    B

    CHECK SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH Click here

    A

  19. CHECK CURRENT DTC


    1. Check for current DTCs Click here.

      Result
      Result Proceed to
      Current DTC B1628 is output. A
      Current DTC B1638 is output. B

      Tech Tips

      Codes other than current DTCs B1628 and B1638 may be output at this time, but they are not related to this check.


    B

    CHECK CONNECTORS Click here

    A

  20. CHECK CONNECTORS


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly LH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  21. CHECK FLOOR WIRE (OPEN)


    1. B000MQOE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-4 (BBL+) - N8-3 (BBL-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.


    NG

    REPLACE FLOOR WIRE

    OK

  22. CHECK FLOOR WIRE (SHORT)

    B000MDBE02
    Text in Illustration
    *1 Side Airbag Sensor Assembly LH
    *2 Airbag Sensor Assembly
    *3 Floor Wire
    *a

    Front view of wire harness connector

    (to Side Airbag Sensor Assembly LH)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-4 (BBL+) - N8-3 (BBL-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  23. CHECK FLOOR WIRE (SHORT TO B+)


    1. B000MDBE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N8-4 (BBL+) - Body ground Engine switch on (IG) Below 1 V
      N8-3 (BBL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    REPLACE FLOOR WIRE

    OK

  24. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B000MDBE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-4 (BBL+) - Body ground Always 1 MΩ or higher
      N8-3 (BBL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  25. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B000IKTE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly

      Connect the connector to the airbag sensor assembly.

    2. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1628 is output. A
      DTC B1623 is output. B
      DTCs B1623 and B1628 are not output. C

      Tech Tips

      Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  26. CHECK CONNECTORS


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  27. CHECK FLOOR WIRE (OPEN)


    1. B000NGZE22
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)
      *b

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)

      Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-1 (BCL+) - N8-2 (BCL-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.


    NG

    REPLACE FLOOR WIRE

    OK

  28. CHECK FLOOR WIRE (SHORT)

    B000HT3E04
    Text in Illustration
    *1 Side No. 2 Airbag Sensor Assembly LH
    *2 Side Airbag Sensor Assembly LH
    *3 Floor Wire
    *a

    Front view of wire harness connector

    (to Side Airbag Sensor Assembly LH)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-1 (BCL+) - N8-2 (BCL-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  29. CHECK FLOOR WIRE (SHORT TO B+)


    1. B000HT3E04
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N8-1 (BCL+) - Body ground Engine switch on (IG) Below 1 V
      N8-2 (BCL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    REPLACE FLOOR WIRE

    OK

  30. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. B000HT3E04
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N8-1 (BCL+) - Body ground Always 1 MΩ or higher
      N8-2 (BCL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  31. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B000IKTE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly

      Connect the connector to the side No. 2 airbag sensor assembly LH.

    2. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1638 is output. A
      DTC B1633 is output. B
      DTCs B1633 and B1638 are not output. C

      Tech Tips

      Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  32. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH


    1. B000HY9E01
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly LH

      Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the engine switch off.

    5. Turn the engine switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1638 is output. A
      DTC B1633 is output. B
      DTCs B1633 and B1638 are not output. C

      Tech Tips

      Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

    7. Turn the engine switch off.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    9. Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  33. CHECK CONNECTORS


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  34. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (OPEN)


    1. B000KT7E17
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Connect the connectors that link the floor wire and front door wire LH.

    2. Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N44-1 (BDL+) - N44-2 (BDL-) Always Below 1 Ω

    NG

    CHECK FRONT DOOR WIRE LH (OPEN) Click here

    OK

  35. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT)


    1. B000N5SE17
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)

      Disconnect the service wire from connector E.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N44-1 (BDL+) - N44-2 (BDL-) Always 1 MΩ or higher

    NG

    CHECK FRONT DOOR WIRE LH (SHORT) Click here

    OK

  36. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)


    1. B000N5SE17
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N44-1 (BDL+) - Body ground Engine switch on (IG) Below 1 V
      N44-2 (BDL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    CHECK FRONT DOOR WIRE LH (SHORT TO B+) Click here

    OK

  37. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)


    1. B000N5SE17
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly LH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N44-1 (BDL+) - Body ground Always 1 MΩ or higher
      N44-2 (BDL-) - Body ground Always 1 MΩ or higher

    NG

    CHECK FRONT DOOR WIRE LH (SHORT TO GROUND) Click here

    OK

  38. CHECK DOOR SIDE AIRBAG SENSOR LH


    1. B000IIWE01
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly LH

      Connect the connectors to the side No. 2 airbag sensor assembly LH.

    2. Interchange the door side airbag sensor LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1697 or B1698 is output. A
      DTC B1692 or B1693 is output. B
      DTCs B1692, B1693, B1697 and B1698 are not output. C

      Tech Tips

      Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the door side airbag sensor LH and RH to their original positions and connect the connectors.


    B

    REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  39. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH


    1. B000HY9E01
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly LH

      Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the engine switch off.

    5. Turn the engine switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1697 or B1698 is output. A
      DTC B1692 or B1693 is output. B
      DTCs B1692, B1693, B1697 and B1698 are not output. C

      Tech Tips

      Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

    7. Turn the engine switch off.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    9. Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  40. CHECK CURRENT DTC


    1. Check for current DTCs Click here.

      Result
      Result Proceed to
      Current DTC B1627 is output. A
      Current DTC B1637 is output. B

      Tech Tips

      Codes other than current DTCs B1627 and B1637 may be output at this time, but they are not related to this check.

    2. Turn the engine switch off.


    B

    CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH Click here

    A

  41. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. B000IKTE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly

      Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

    3. Connect the cable to the negative (-) battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1627 is output. A
      DTC B1622 is output. B
      DTCs B1622 and B1627 are not output. C

      Tech Tips

      Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  42. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH


    1. B000HY9E01
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly LH

      Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1637 is output. A
      DTC B1632 is output. B
      DTCs B1632 and B1637 are not output. C

      Tech Tips

      Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.


    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  43. CHECK FRONT DOOR WIRE LH (OPEN)


    1. B000M7WE07
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Floor Wire)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      Disconnect the front door wire LH connector from the floor wire.

      Tech Tips

      The service wire has already been inserted into connector E.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      KN1-1 (BDL+) - KN1-2 (BDL-) Always Below 1 Ω

    3. Disconnect the service wire from connector E.


    NG

    REPLACE FRONT DOOR WIRE LH

    OK

    REPLACE FLOOR WIRE

  44. CHECK FRONT DOOR WIRE LH (SHORT)


    1. B000IYUE02
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Floor Wire)

      Disconnect the front door wire LH connector from the floor wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      KN1-1 (BDL+) - KN1-2 (BDL-) Always 1 MΩ or higher

    NG

    REPLACE FRONT DOOR WIRE LH

    OK

    REPLACE FLOOR WIRE

  45. CHECK FRONT DOOR WIRE LH (SHORT TO B+)


    1. B000IYUE02
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Floor Wire)

      Disconnect the front door wire LH connector from the floor wire.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the engine switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      KN1-1 (BDL+) - Body ground Engine switch on (IG) Below 1 V
      KN1-2 (BDL-) - Body ground Engine switch on (IG) Below 1 V

    NG

    REPLACE FRONT DOOR WIRE LH

    OK

    REPLACE FLOOR WIRE

  46. CHECK FRONT DOOR WIRE LH (SHORT TO GROUND)


    1. B000IYUE02
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly LH
      *3 Front Door Wire LH
      *4 Floor Wire
      *a

      Front view of wire harness connector

      (to Floor Wire)

      Disconnect the front door wire LH connector from the floor wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      KN1-1 (BDL+) - Body ground Always 1 MΩ or higher
      KN1-2 (BDL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FRONT DOOR WIRE LH

    OK

    REPLACE FLOOR WIRE