BLIND SPOT MONITOR SYSTEM, Diagnostic DTC:C1AB2

DTC Code DTC Name
C1AB2 Short to GND in Outer Mirror Indicator(Master)

DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a ground short in the outer rear view mirror indicator RH.

DTC No. DTC Detection Condition Trouble Area
C1AB2

    When either of the following conditions is met:

  • Blind spot monitor main switch (warning canceling switch assembly) is on.


  • The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time.

  • Outer rear view mirror RH (outer rear view mirror indicator RH)

  • Outer rear view mirror assembly RH

  • Wire harness or connector

  • Blind spot monitor sensor RH

  • Outer mirror control ECU assembly RH

WIRING DIAGRAM

B000KKCE35

INSPECTION PROCEDURE

Note

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

    NG

    CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH) Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  2. CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)


    1. Disconnect the O43 blind spot monitor sensor RH connector.

    2. Disconnect the J10 outer mirror control ECU assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Always
      J10-10 (BDSR) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)


    1. Disconnect the z17 outer mirror control ECU assembly RH connector.

    2. Disconnect the IND2 outer rear view mirror RH (outer rear view mirror indicator RH) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z17-7 (BSM+) - Body ground Always 10 kΩ or higher

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

    OK

  4. INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH


    1. Disconnect the J10 outer mirror control ECU assembly RH connector.

    2. B000IHME48
      Text in Illustration
      *a

      Component without harness connected

      (Outer Mirror Control ECU Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J10-10 (BDSR) - Body ground Always 10 kΩ or higher

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH Click here

    OK

  5. INSPECT OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)


    1. Remove the outer rear view mirror RH (outer rear view mirror indicator RH) Click here.

    2. Inspect the outer rear view mirror indicator RH on the outer rear view mirror RH Click here.


    NG

    REPLACE OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)) Click here

    OK

  6. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

    NG

    REPLACE BLIND SPOT MONITOR SENSOR RH Click here

    OK

    END (OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH) WAS DEFECTIVE)