NOISE FILTER (for TMMK Made) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. B000M41E01

      Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

    2. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  4. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. B000LZB

      Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  5. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide.

    2. Disconnect the connector.

    3. B000HU6

      Remove the 2 bolts.

    4. Disengage the hook and remove the rear side seatback assembly LH.

  6. REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)

    Note

    When the terminal covers are removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.


    1. B000LWD

      Remove the bolt.

    2. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. B000MKO

      Disengage the claw and pull out the cover as shown in the illustration.

    4. B000N84

      Using a screwdriver, disengage the 6 claws and remove the 2 terminal covers with wire harness from the condenser.

    5. B000LFB

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

    6. Remove the terminal cover from the wire harness.

      Note


      • Make sure to hold the wire harness on the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.

  7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Window Defogger)


    1. Disconnect the rear door opening trim weatherstrip LH.

  8. REMOVE ROOF SIDE INNER GARNISH LH (for Window Defogger)


    1. B000NIP

      Disengage the 5 clips.

    2. Disengage the guide and remove the roof side inner garnish LH.

    3. Remove the 5 clips from the roof side inner garnish LH.

  9. REMOVE RADIO SETTING CONDENSER (for Window Defogger)

    Note

    When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


    1. B000HWR

      Remove the bolt.

    2. Disengage the 2 clamps and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. B000M7H

      Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.

    4. B000MEK

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

    5. Remove the terminal cover from the wire harness.

      Note


      • Make sure to hold the wire harness on the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.