ENGINE SWITCH REMOVAL


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the auto away/return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the auto away/return function is enabled or disabled) in order to restore the current setting after finishing this operation.

      Tech Tips

      Performing the above operation disables the auto away/return function when the ignition switch is turned off.

    2. Turn the ignition switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the ignition switch off and disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click here.

  5. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click here.

  6. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B000N47

      Disengage the 10 claws and remove the front door scuff plate LH.

  7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. B000MCM

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. B000HXQ

      Disconnect the front door opening trim weatherstrip LH.

  9. REMOVE INSTRUMENT SIDE PANEL LH


    1. B000HH8

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. B000MY7

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  10. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B000J4N

      Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.

  11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. for Manual Tilt and Manual Telescopic Steering Column:


      1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. B000MKZ

      Using a moulding remover, disengage the 4 clips and 2 guides.

    3. for LHD:


      1. B000HY1

        Disengage the 3 claws, 7 clips and 4 guides.

    4. for RHD:


      1. B000HJQ

        Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.

    5. Disconnect each connector.

    6. B000KKH

      Remove the instrument cluster finish panel assembly as shown in the illustration.

  12. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B000H4N

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  13. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY


    1. B000MW9

      Remove the 2 bolts <B>.

    2. w/o Driver Side Knee Airbag:


      1. B000KQ0

        Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.

    3. w/ Driver Side Knee Airbag:


      1. B000KAO

        Disengage the 4 claws, 7 clips and 3 guides to remove the instrument panel sub-assembly.

  14. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    1. B000I30

      Remove the 2 screws <D>.

    2. B000HWD

      Disengage the 2 clips as shown in the illustration.

    3. Disconnect each connector to remove the front ash receptacle assembly.

  15. REMOVE CONSOLE BOX ASSEMBLY

    Click here.

  16. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. for LHD:


      1. B000MWF

        Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. B000HGW

      Remove the 2 screws <D>.

    3. B000HQ9

      Disengage the clip and 4 guides to remove the front No. 2 console box insert as shown in the illustration.

  17. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. B000LT8

      Disengage the 3 clips and guide to remove the lower instrument panel finish panel assembly.

    2. for LHD with Smart Entry and Start System:


      1. Disconnect the connector.

  18. REMOVE ENGINE SWITCH


    1. B000HRF

      Disengage the 2 claws and remove the engine switch.