LOWER INSTRUMENT PANEL(for Hatchback, Wagon) REMOVAL

PROCEDURE


  1. PRECAUTION

    Click here

  2. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

    Click here

  3. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  5. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  6. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD)


    1. A01TBHA

      Disengage the 8 clips.

    2. Disconnect each connector to remove the lower instrument cluster finish panel assembly.

  7. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for RHD)


    1. w/o Entry and Start System:


      1. A01TCN6

        Disengage the claw and 6 clips.

      2. Disconnect each connector to remove the lower instrument cluster finish panel assembly.

    2. w/ Entry and Start System:


      1. A01TB3N

        Disengage the 8 clips.

      2. Disconnect each connector to remove the lower instrument cluster finish panel assembly.

  8. REMOVE NO. 2 SWITCH HOLE BASE (for LHD)


    1. A01TC11

      Disengage the 3 clips to remove the No. 2 switch hole base as shown in the illustration.

  9. REMOVE NO. 2 SWITCH HOLE BASE (for RHD)


    1. w/o Entry and Start System:


      1. A01TAFG

        Disengage the 5 clips and remove the No. 2 switch hole base as shown in the illustration.

    2. w/ Entry and Start System:


      1. A01TAQY

        Disengage the 4 clips as shown in the illustration.

      2. Disconnect the connector to remove the No. 2 switch hole base.

  10. REMOVE NO. 1 SWITCH HOLE BASE (for LHD)


    1. w/o Entry and Start System:


      1. A01TAF5

        Disengage the 4 clips to remove the No. 1 switch hole base.

    2. w/ Entry and Start System:


      1. A01T9YX

        Disengage the 4 clips as shown in the illustration.

      2. Disconnect the connector to remove the No. 1 switch hole base.

  11. REMOVE NO. 1 SWITCH HOLE BASE (for RHD)


    1. A01TAZW

      Disengage the 4 clips as shown in the illustration.

    2. Disconnect the connector to remove the No. 1 switch hole base.

  12. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)


    1. A01TDSJ

      Remove the 2 screws <E>.

    2. A01T9NS

      Disengage the claw and guide to remove the No. 1 instrument panel under cover sub-assembly.

  13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)


    1. A01TA5D

      Disengage the 7 clips to remove the lower instrument panel finish panel sub-assembly.

  14. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

    Click here

  15. REMOVE STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01TBDX

      Remove the 4 bolts <B>.

    2. Disengage the 2 guides.

    3. Disconnect the connector to remove the stereo opening cover with bracket.

  16. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

    Click here

  17. REMOVE NO. 1 NAVIGATION ANTENNA CORD SUB-ASSEMBLY (w/ Navigation System)

    Click here

  18. REMOVE CENTER INSTRUMENT PANEL SAFETY PAD RETAINER WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  19. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  20. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)


    1. A01TDR3

      Disengage the 3 claws and guide to remove the No. 2 instrument panel under cover sub-assembly.

  22. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A01T9FYC01
      *1 Glove Compartment Door Stopper Sub-assembly
      *a Stopper

      Disengage the claw to disconnect the glove compartment door stopper sub-assembly.

    2. Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and open the glove compartment door assembly until the stoppers are released.

    3. A01TBR7C01
      *a Close
      *b Open approximately 53°

      Open the glove compartment door assembly to approximately 53° from its closed position. Pull it horizontally in the direction indicated by the arrow to disengage the 2 hinges and remove the glove compartment door assembly.

      Note

      Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.

  23. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    1. A01TB0C

      Disengage the claw to remove the glove compartment door stopper sub-assembly.

  24. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01TA5C

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  25. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Disengage each clamp.

      A01T8KPC04
      *1 cooler (room temp. sensor) thermistor - -
      *a DLC3 - -

    2. Disconnect each connector.

    3. Disengage the 2 claws and disconnect the DLC3.

    4. for Automatic Air Conditioning System:


      1. Disengage the 2 claws to disconnect the cooler (room temp. sensor) thermistor.

    5. Remove the 2 bolts <A>, 8 screws <C>, screw <D> and lower instrument panel sub-assembly.

      A01TACBC04
      *a Bolt <A> *b Screw <C>
      *c Screw <D> - -