REAR BRAKE REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.

  • Refer to the illustration to confirm the type of brake caliper.

    A01LVHFC01
    *A for Type A *B for Type B
    *C for Double Wishbone Type Suspension *D for Torsion Beam Type Suspension

PROCEDURE


  1. REMOVE REAR WHEEL

  2. DRAIN BRAKE FLUID

    Note

    If brake fluid leaks onto any painted surface, immediately wash it off.

  3. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

    for Hatchback, Wagon: Click here

    for Sedan: Click here

  4. LOOSEN NO. 2 WIRE ADJUSTING NUT

    Click here

  5. REMOVE PARKING BRAKE LEVER PROTECTOR (for Double Wishbone Type Suspension)

    Click here

  6. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Torsion Beam Type Suspension)


    1. A01M1N6

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

    2. A01LYIBC01
      *1 Clip
      *2 Rear Disc Brake Cylinder Assembly

      Disengage the clip and separate the No. 3 parking brake cable assembly.

  7. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Double Wishbone Type Suspension)


    1. A01LYKZ

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

    2. A01M1BZC01
      *1 Clip
      *2 Rear Disc Brake Cylinder Assembly

      Disengage the clip and separate the No. 3 parking brake cable assembly.

  8. DISCONNECT REAR FLEXIBLE HOSE


    1. A01LWRB

      Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.

  9. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY


    1. A01M3D0C01
      *a Hold
      *b Turn

      Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.

      Note

      Remove the rear disc brake cylinder assembly while holding both of the rear disc brake pads because the anti-squeal springs may fall off the rear disc brake pads (for Type B).

  10. REMOVE REAR DISC BRAKE PAD


    1. for Type A:


      1. A01M2W2

        Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.

    2. for Type B:


      1. A01LWDS

        Remove the 2 anti-squeal springs from the rear disc brake pads.

      2. A01M0GD

        Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.

  11. REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM


    1. for Type B:


      1. Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from each rear disc brake pad.

  12. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE


    1. for Type A:


      1. A01M1ZG

        Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.

        Note

        Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.

    2. for Type B:


      1. A01M2B5

        Remove the 2 rear disc brake pad support plates from the rear disc brake cylinder mounting.

        Note

        Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.

  13. REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN


    1. for Type A:


      1. A01M3EI

        Remove the 2 rear disc brake cylinder slide pins from the rear disc brake cylinder mounting.

      2. A01LWQSC02
        *a Protective Tape

        Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the disc brake cylinder slide pin (for upper side).

        Note

        Do not damage the rear disc brake cylinder slide pin (for upper side).

    2. for Type B:


      1. A01LUYV

        Remove the 2 rear disc brake cylinder slide pins from the rear disc brake cylinder mounting.

      2. A01LW48C13
        *a Protective Tape

        Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from each rear disc brake cylinder slide pin.

        Note

        Do not damage the rear disc brake cylinder slide pin.

  14. REMOVE REAR DISC BRAKE BUSHING DUST BOOT


    1. A01LVOG

      Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.

  15. REMOVE REAR DISC BRAKE CYLINDER MOUNTING


    1. A01M2MG

      Remove the 2 bolts and rear disc brake cylinder mounting.

  16. REMOVE REAR DISC


    1. A01M109C01
      *a Matchmark

      Put matchmarks on the rear disc and the rear axle hub and bearing assembly.

    2. Remove the rear disc.