LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2325

DTC Code DTC Name
B2325 LIN Communication Bus Malfunction

DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2325 LIN Communication Bus Malfunction Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.

  • Front door window regulator assembly (for driver door)

  • Front door window regulator assembly (for front passenger door)*1

  • Rear door window regulator assembly (for RH door)*1

  • Rear door window regulator assembly (for LH door)*1

  • Power window regulator master switch assembly*1

  • Roof sunshade ECU (sliding roof drive gear assembly)*2

  • Double lock door control relay assembly*3

  • Main body ECU (multiplex network body ECU)

  • Instrument panel junction block assembly

  • Wire harness or connector

  • DOOR NO. 2 fuse

  • DOOR NO. 1 fuse*1

  • ECU-B NO. 2 fuse*1

  • DOOR R/R fuse*1

  • DOOR R/L fuse*1

  • S-ROOF fuse*2

  • D/L NO. 2 fuse*3

  • ECU-B NO. 1 fuse*3

WIRING DIAGRAM


  1. for Models with Jam Protection Function on 4 Windows


    1. for LHD

      A00Y5OME06

    2. for RHD

      A00Y75DE08

  2. for Models with Jam Protection Function on Driver Door Window Only

    A00YA2AE09

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When a door window regulator assembly is replaced or removed and reinstalled, it requires initialization.

    for Models with Jam Protection Function on 4 Windows: Click here

    for Models with Jam Protection Function on Driver Door Window Only: Click here

  • When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it requires initialization (w/ Roof Sunshade System).

    Click here

  • Before performing the inspection, check that DTC B1206, B1249, B1273, B2321, B2322, B2323 or B2324 is not output.

    Click here

PROCEDURE


  1. SYSTEM CHECK


    1. Check the vehicle specifications.

      Result
      Result Proceed to
      for Models with Jam Protection Function on 4 Windows A
      for Models with Jam Protection Function on Driver Door Window Only B

    B

    INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    A

  2. CHECK HARNESS AND CONNECTOR (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door) - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)


    1. for LHD


      1. Disconnect the H12 power window regulator master switch assembly connector.

      2. Disconnect the H14 front door window regulator assembly (for driver door) connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        H12-16 (LIN2) - H14-9 (LIN) Always Below 1 Ω
        H12-16 (LIN2) - Body ground Always 10 kΩ or higher
        H14-9 (LIN) - Body ground Always 10 kΩ or higher

    2. for RHD


      1. Disconnect the G3 power window regulator master switch assembly connector.

      2. Disconnect the G5 front door window regulator assembly (for driver door) connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        G3-16 (LIN2) - G5-9 (LIN) Always Below 1 Ω
        G3-16 (LIN2) - Body ground Always 10 kΩ or higher
        G5-9 (LIN) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. A00Y8XIC05
      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly)

      Remove the power window regulator master switch assembly.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      16 (LIN2) - 17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    OK

  4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      for LHD: Click here

      for RHD: Click here

      A00Y6GHC02
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tech Tips

      This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance
      Tester Connection Condition Specified Condition
      3C-22 - MB-16 (LIN2) Always Below 1 Ω
      3E-29 - MB-16 (LIN2) Always Below 1 Ω
      3E-14 - MB-16 (LIN2) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY for LHD: Click here
    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY for RHD: Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)


    1. for LHD


      1. Disconnect the H12 power window regulator master switch assembly connector.

      2. Disconnect the G13 front door window regulator assembly (for front passenger door) connector.

      3. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.*

      4. Disconnect the K3 rear door window regulator assembly (for LH door) connector.

      5. Disconnect the J3 rear door window regulator assembly (for RH door) connector.

      6. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3C-22 - H12-17 (LIN1) Always Below 1 Ω
        3C-22 - a1-11 (LIN)* Always Below 1 Ω
        3C-22 - G13-9 (LIN) Always Below 1 Ω
        3E-29 - K3-9 (LIN) Always Below 1 Ω
        3E-14 - J3-9 (LIN) Always Below 1 Ω
        3C-22 - Body ground Always 10 kΩ or higher
        3E-29 - Body ground Always 10 kΩ or higher
        3E-14 - Body ground Always 10 kΩ or higher
        H12-17 (LIN1) - Body ground Always 10 kΩ or higher
        a1-11 (LIN) - Body ground* Always 10 kΩ or higher
        G13-9 (LIN) - Body ground Always 10 kΩ or higher
        K3-9 (LIN) - Body ground Always 10 kΩ or higher
        J3-9 (LIN) - Body ground Always 10 kΩ or higher

        • *: w/ Roof Sunshade System

    2. for RHD


      1. Disconnect the G3 power window regulator master switch assembly connector.

      2. Disconnect the H4 front door window regulator assembly (for front passenger door) connector.

      3. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.*1

      4. Disconnect the E107 double lock door control relay assembly connector.*2

      5. Disconnect the K3 rear door window regulator assembly (for LH door) connector.

      6. Disconnect the J3 rear door window regulator assembly (for RH door) connector.

      7. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3C-22 - G3-17 (LIN1) Always Below 1 Ω
        3C-22 - a1-11 (LIN)*1 Always Below 1 Ω
        3C-22 - H4-9 (LIN) Always Below 1 Ω
        3C-22 - E107-9 (MPX1)*2 Always Below 1 Ω
        3E-14 - K3-9 (LIN) Always Below 1 Ω
        3E-29 - J3-9 (LIN) Always Below 1 Ω
        3C-22 - Body ground Always 10 kΩ or higher
        3E-29 - Body ground Always 10 kΩ or higher
        3E-14 - Body ground Always 10 kΩ or higher
        G3-17 (LIN1) - Body ground Always 10 kΩ or higher
        a1-11 (LIN) - Body ground*1 Always 10 kΩ or higher
        H4-9 (LIN) - Body ground Always 10 kΩ or higher
        E107-9 (MPX1) - Body ground*2 Always 10 kΩ or higher
        K3-9 (LIN) - Body ground Always 10 kΩ or higher
        J3-9 (LIN) - Body ground Always 10 kΩ or higher

        • *1: w/ Roof Sunshade System

        • *2: w/ Double Locking System

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK DTC OUTPUT (REAR DOOR WINDOW REGULATOR ASSEMBLY (for LH Door))


    1. for LHD


      1. Reconnect the H12 power window regulator master switch assembly connector.

      2. Reconnect the 3C and 3E instrument panel junction block assembly connector.

      3. Reconnect the H14 front door window regulator assembly (for driver door) connector.

      4. Reconnect the G13 front door window regulator assembly (for front passenger door) connector.

      5. Reconnect the J3 rear door window regulator assembly (for RH door) connector.

      6. Reconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.*


        • *: w/ Roof Sunshade System

      7. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      8. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes

    2. for RHD


      1. Reconnect the G3 power window regulator master switch assembly connector.

      2. Reconnect the 3C and 3E instrument panel junction block assembly connector.

      3. Reconnect the G5 front door window regulator assembly (for driver door) connector.

      4. Reconnect the H4 front door window regulator assembly (for front passenger door) connector.

      5. Reconnect the J3 rear door window regulator assembly (for RH door) connector.

      6. Reconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.*1


        • *1: w/ Roof Sunshade System

      7. Reconnect the E107 double lock door control relay assembly connector.*2


        • *2: w/ Double Locking System

      8. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      9. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE REAR DOOR WINDOW REGULATOR ASSEMBLY (for LH Door) Click here

    A

  7. CHECK DTC OUTPUT (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)


    1. for LHD


      1. Reconnect the K3 rear door window regulator assembly (for LH door) connector.

      2. Disconnect the H12 power window regulator master switch assembly connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes

    2. for RHD


      1. Reconnect the K3 rear door window regulator assembly (for LH door) connector.

      2. Disconnect the G3 power window regulator master switch assembly connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    A

  8. CHECK DTC OUTPUT (REAR DOOR WINDOW REGULATOR ASSEMBLY (for RH Door))


    1. for LHD


      1. Reconnect the H12 power window regulator master switch assembly connector.

      2. Disconnect the J3 rear door window regulator assembly (for RH door) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes

    2. for RHD


      1. Reconnect the G3 power window regulator master switch assembly connector.

      2. Disconnect the J3 rear door window regulator assembly (for RH door) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE REAR DOOR WINDOW REGULATOR ASSEMBLY (for RH Door) Click here

    A

  9. CHECK DTC OUTPUT (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door))


    1. for LHD


      1. Reconnect the J3 rear door window regulator assembly (for RH door) connector.

      2. Disconnect the H14 front door window regulator assembly (for driver door) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes

    2. for RHD


      1. Reconnect the J3 rear door window regulator assembly (for RH door) connector.

      2. Disconnect the G5 front door window regulator assembly (for driver door) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door) Click here

    A

  10. CHECK DTC OUTPUT (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Front Passenger Door))


    1. for LHD


      1. Reconnect the H14 front door window regulator assembly (for driver door) connector.

      2. Disconnect the G13 front door window regulator assembly (for front passenger door) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes

    2. for RHD


      1. Reconnect the G5 front door window regulator assembly (for driver door) connector.

      2. Disconnect the H4 front door window regulator assembly (for front passenger door) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output (w/ Roof Sunshade System) A
      DTC B2325 is output (w/ Double Locking System and w/o Roof Sunshade System) B
      DTC B2325 is output (w/o Double Locking System and w/o Roof Sunshade System) C
      DTC B2325 is not output D

    B

    CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY) Click here

    C

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here
    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here

    D

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Front Passenger Door) Click here

    A

  11. CHECK DTC OUTPUT (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))


    1. for LHD


      1. Reconnect the G13 front door window regulator assembly (for front passenger door) connector.

      2. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes

    2. for RHD


      1. Reconnect the H4 front door window regulator assembly (for front passenger door) connector.

      2. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output (w/ Double Locking System) A
      DTC B2325 is output (w/o Double Locking System) B
      DTC B2325 is not output C

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here
    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here

    C

    REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) Click here

    A

  12. CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)


    1. Reconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

    2. Disconnect the E107 double lock door control relay assembly connector.

    3. Clear the DTCs.

      Click here


      Body Electrical > Main Body > Clear DTCs

    4. After 10 seconds have elapsed, check if the same DTC is output again.


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY Click here

  13. CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)


    1. Reconnect the H4 front door window regulator assembly (for front passenger door) connector.

    2. Disconnect the E107 double lock door control relay assembly connector.

    3. Clear the DTCs.

      Click here


      Body Electrical > Main Body > Clear DTCs

    4. After 10 seconds have elapsed, check if the same DTC is output again.


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY Click here

  14. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      for LHD: Click here

      for RHD: Click here

      A00Y8B3C03
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tech Tips

      This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance
      Tester Connection Condition Specified Condition
      3C-22 - MB-16 (LIN2) Always Below 1 Ω
      3C-23 - MB-16 (LIN2) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY for LHD: Click here
    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY for RHD: Click here

    OK

  15. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)


    1. for LHD


      1. Disconnect the H14 front door window regulator assembly (for driver door) connector.

      2. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.*

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3C-23 - H14-9 (LIN) Always Below 1 Ω
        3C-22 - a1-11 (LIN)* Always Below 1 Ω
        3C-22 - Body ground Always 10 kΩ or higher
        3C-23 - Body ground Always 10 kΩ or higher
        a1-11 (LIN) - Body ground* Always 10 kΩ or higher
        H14-9 (LIN) - Body ground Always 10 kΩ or higher

        • *: w/ Roof Sunshade System

    2. for RHD


      1. Disconnect the G5 front door window regulator assembly (for driver door) connector.

      2. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.*1

      3. Disconnect the E107 double lock door control relay assembly connector.*2

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3C-23 - G5-9 (LIN) Always Below 1 Ω
        3C-22 - a1-11 (LIN)*1 Always Below 1 Ω
        3C-22 - E107-9 (MPX1)*2 Always Below 1 Ω
        3C-22 - Body ground Always 10 kΩ or higher
        3C-23 - Body ground Always 10 kΩ or higher
        a1-11 (LIN) - Body ground*1 Always 10 kΩ or higher
        E107-9 (MPX1) - Body ground*2 Always 10 kΩ or higher
        G5-9 (LIN) - Body ground Always 10 kΩ or higher

        • *1: w/ Roof Sunshade System

        • *2: w/ Double Locking System

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  16. CHECK DTC OUTPUT (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door))


    1. for LHD


      1. Reconnect the 3C instrument panel junction block assembly connector.

      2. Reconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.*


        • *: w/ Roof Sunshade System

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes

    2. for RHD


      1. Reconnect the 3C instrument panel junction block assembly connector.

      2. Reconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.*1


        • *1: w/ Roof Sunshade System

      3. Reconnect the E107 double lock door control relay assembly connector.*2


        • *2: w/ Double Locking System

      4. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      5. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output (w/ Roof Sunshade System) A
      DTC B2325 is output (w/ Double Locking System and w/o Roof Sunshade System) B
      DTC B2325 is output (w/o Double Locking System and w/o Roof Sunshade System) C
      DTC B2325 is not output D

    B

    CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY) Click here

    C

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here
    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here

    D

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door) Click here

    A

  17. CHECK DTC OUTPUT (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))


    1. for LHD


      1. Reconnect the H14 front door window regulator assembly (for driver door) connector.

      2. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes

    2. for RHD


      1. Reconnect the G5 front door window regulator assembly (for driver door) connector.

      2. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

      3. Clear the DTCs.

        Click here


        Body Electrical > Main Body > Clear DTCs

      4. After 10 seconds have elapsed, check if the same DTC is output again.


        Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output (w/ Double Locking System) A
      DTC B2325 is output (w/o Double Locking System) B
      DTC B2325 is not output C

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here
    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here

    C

    REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) Click here

    A

  18. CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)


    1. Reconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

    2. Disconnect the E107 double lock door control relay assembly connector.

    3. Clear the DTCs.

      Click here


      Body Electrical > Main Body > Clear DTCs

    4. After 10 seconds have elapsed, check if the same DTC is output again.


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY Click here

  19. CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)


    1. Reconnect the G5 front door window regulator assembly (for driver door) connector.

    2. Disconnect the E107 double lock door control relay assembly connector.

    3. Clear the DTCs.

      Click here


      Body Electrical > Main Body > Clear DTCs

    4. After 10 seconds have elapsed, check if the same DTC is output again.


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY Click here