ROOF HEADLINING REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. OPEN BACK DOOR


    1. Open the back door before disconnecting the cable from the negative (-) battery terminal, as some procedures are performed with the back door open.

      Note

      The back door cannot be opened after the cable is disconnected from the negative (-) battery terminal.

  2. REMOVE UPPER RADIATOR SUPPORT SEAL

    Click here

  3. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE REAR NO. 2 SEAT ASSEMBLY LH

    Click here

  6. REMOVE REAR NO. 2 SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  7. REMOVE FRONT DOOR SCUFF PLATE LH


    1. w/o Illumination:


      1. B001973

        Detach the 7 claws and 4 clips and remove the front door scuff plate LH.

    2. w/ Illumination:


      1. B0018EY

        Detach the 7 claws and 4 clips.

      2. Disconnect the connector and remove the front door scuff plate LH.

  8. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  9. REMOVE REAR STEP COVER

    Tech Tips

    Use the same procedure for both rear step covers.


    1. w/o Illumination Type Front Door Scuff Plate:


      1. B0019YG

        Detach the 2 claws and remove the rear step cover.

    2. w/ Illumination Type Front Door Scuff Plate:


      1. B0019FG

        Detach the 4 claws and remove the rear step cover.

  10. REMOVE REAR DOOR SCUFF PLATE LH


    1. w/o Illumination Type Front Door Scuff Plate:


      1. B001AXP

        Remove the screw.

      2. Detach the 3 claws and 4 clips and remove the rear door scuff plate LH.

    2. w/ Illumination Type Front Door Scuff Plate:

      Remove the rear door scuff plate.


      1. B0018KA

      2. Detach the 3 claws and 4 clips and remove the rear door scuff plate LH.

  11. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  12. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    B0019OG

    1. Detach the 6 clips and 4 claws and remove the rear floor mat support plate.

  13. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Click here

  14. REMOVE FRONT PILLAR GARNISH LH

    Click here

  15. REMOVE FRONT PILLAR GARNISH RH

    Click here

  16. REMOVE CENTER PILLAR GARNISH COVER LH

    Tech Tips


    • When removing the center pillar garnish cover LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B0018G3

      Detach the 2 clips and 2 guides and remove the center pillar garnish cover LH.

  17. REMOVE CENTER PILLAR GARNISH COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  18. REMOVE CENTER LOWER PILLAR GARNISH LH

    Tech Tips


    • When removing the center lower pillar garnish LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B0018B6

      Remove the bolt and seat belt anchor.

    2. B0018U2

      Detach the 2 claws and 7 clips and remove the center lower pillar garnish LH.

  19. REMOVE CENTER LOWER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  20. REMOVE REAR ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for both rear assist grip assemblies.


    1. B001AI8

      Detach the 4 claws and remove the 2 assist grip plugs.

    2. B0018QZ

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the rear assist grip assembly.

  21. REMOVE CENTER PILLAR GARNISH LH

    B0018EH

    1. Remove the bolt.

    2. Detach the 2 clips and 2 guides.

    3. Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish LH.

  22. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  23. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    B00192K

    Tech Tips

    When removing the front quarter trim panel assembly LH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. B00190O

      Detach the 3 claws and remove the outer lap belt anchor cover.

    2. B0019R5

      Remove the bolt and rear No. 1 seat belt anchor.

    3. B001AD7

      Remove the bolt and rear No. 2 seat belt anchor.

    4. Remove the clip.

    5. Detach the 19 clips and 2 claws.

    6. Disconnect the thermistor connector and then remove the front quarter trim panel assembly LH.

      B0018RJ

  24. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    B0019I8

    Tech Tips

    When removing the front quarter trim panel assembly RH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. B0019WZ

      Detach the 3 claws and remove the outer lap belt anchor cover.

    2. B001AC1

      Remove the bolt and rear No. 1 seat belt anchor.

    3. B001APB

      Detach the 3 claws and remove the outer lap belt anchor cover.

    4. B0018NQ

      Remove the bolt and rear No. 2 seat belt anchor.

    5. Remove the clip.

    6. Detach the 17 clips and 2 claws.

    7. Disconnect the thermistor connector and then remove the front quarter trim panel assembly RH.

      B001977

  25. REMOVE REAR FRONT QUARTER TRIM GARNISH LH

    B0019M9

    1. Remove the screw.

    2. Detach the clip and 2 guides.

    3. Pass the seat belt anchor through the rear front quarter trim garnish LH, and remove the rear front quarter trim garnish LH.

  26. REMOVE REAR FRONT QUARTER TRIM GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  27. REMOVE REAR UPPER PILLAR GARNISH LH

    B00183L

    1. Using a moulding remover B, detach the 2 claws and open the seat belt shoulder anchor cover.

    2. B00189W

      Remove the bolt and seat belt shoulder anchor.

    3. B001ABF

      Detach the 5 clips and remove the rear upper pillar garnish LH.

  28. REMOVE CENTER BACK DOOR GARNISH (w/ Power Back Door)

    Click here

  29. REMOVE BACK DOOR SIDE GARNISH RH (w/ Power Back Door)

    Click here

  30. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)

    Click here

  31. REMOVE REAR UPPER PILLAR GARNISH RH

    B001B06

    1. Using a moulding remover, detach the 2 claws and open the seat belt shoulder anchor cover.

    2. B0019D0

      Remove the bolt and seat belt shoulder anchor.

    3. w/o Power Back Door:


      1. B0018VH

        Detach the 5 clips and remove the rear upper pillar garnish RH.

    4. w/ Power Back Door:


      1. B001ASAE01
        Text in Illustration
        *a Power Back Door Rod

        Detach the 5 clips.

      2. Pass the power back door rod through the rear upper pillar garnish, and remove the rear upper pillar garnish RH.

  32. REMOVE MAP LIGHT ASSEMBLY

    Click here

  33. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    Click here

  34. REMOVE NO. 3 ROOM LIGHT ASSEMBLY

    Click here

  35. REMOVE VISOR BRACKET COVER

    Tech Tips

    Use the same procedure for both visor bracket covers.


    1. B001AMR

      Detach the 4 claws and remove the visor bracket cover.

  36. REMOVE VISOR ASSEMBLY LH

    B00191I

    1. Remove the 2 screws and visor assembly LH.

  37. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  38. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedure for both visor holders.


    1. B001AD0E02

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  39. REMOVE CENTER VISOR ASSEMBLY LH

    B0019EME01
    Text in Illustration
    *a Protective Tape
    *b Cover

    1. Using a screwdriver, pry off the cover to detach the 2 clips and remove the center visor assembly LH.

      Tech Tips

      Tape the screwdriver tip before use.

  40. REMOVE CENTER VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  41. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/o Pre-crash Safety System)

    Click here

  42. REMOVE RAIN SENSOR COVER

    Click here

  43. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  44. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  45. REMOVE SEAT BELT ANCHOR COVER

    B001ADP

    1. Detach the 4 clips and 4 guides, and remove the seat belt anchor cover.

  46. REMOVE ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for both assist grip assemblies.


    1. B001856E01
      Text in Illustration
      *a Protective Tape

      Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip assembly.

    3. Remove the 2 clips from the vehicle body.

  47. REMOVE NO. 2 ASSIST GRIP ASSEMBLY LH

    B0019NKE01
    Text in Illustration
    *a Protective Tape

    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the No. 2 assist grip assembly LH.

    3. Remove the 2 clips from the vehicle body.

  48. REMOVE NO. 2 ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  49. REMOVE 3RD SEAT ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for both 3rd seat assist grip assemblies.


    1. B001AHOE01
      Text in Illustration
      *a Protective Tape

      Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the 3rd seat assist grip assembly.

    3. Remove the 2 clips from the vehicle body.

  50. REMOVE ROOF HEADLINING ASSEMBLY

    B0018GF

    Tech Tips


    • When removing the roof headlining assembly, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

    • After moving the seats, disconnect the cable from the negative (-) battery terminal.


    1. B0018EA

      w/o Pre-crash Safety System:

      Disconnect the connector.

    2. B0018PH

      Disconnect the connector.

    3. w/ Pre-crash Safety System:


      1. B0018UU

        w/o Camera Heater:

        Disconnect the 2 connectors.

      2. B001AE2

        w/ Camera Heater:

        Disconnect the 3 connectors.

    4. B0018WT

      Disconnect the connector.

    5. B0018B2E01

      Disconnect the 3 roof wire connectors and washer hose.

    6. Detach the 4 clamps.

      Text in Illustration
      *a Front Left Side
      *b Washer Hose
    7. B001AOBE01

      Remove the bolt.

    8. Disconnect the antenna cord connector and detach the 2 clamps.

      Text in Illustration
      *a Front Right Side
    9. B001AY8E01
      Text in Illustration
      *a Rear Right Side

      Disconnect the antenna cord connector.

    10. B001B3PE05
      Text in Illustration
      *a Rear Left Side

      Disconnect the washer hose.

    11. Detach the 12 claws, 2 clips, 2 guides and 16 fasteners.

      B001839E01
      Text in Illustration
      *a Guide - -
    12. B001AL8

      Remove the roof headlining assembly from the rear of the vehicle as shown in the illustration.

      Note

      Be careful not to damage the roof headlining assembly when taking it out.

  51. REMOVE FRONT ROOF SIDE RAIL GARNISH LH

    B001AAK

    1. Pull the front roof side rail garnish LH to detach the 3 clips.

    2. B0019YQE01

      Turn the end of the clip 90° with needle-nose pliers and disconnect it from the front roof side rail garnish LH and remove the front roof side rail garnish LH.

      Note


      • Clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the clips with new ones if they are removed from the vehicle.

      Tech Tips


      • Use the same procedure for the other clip.

      • Tape the tips of the needle-nose pliers before use.

      Text in Illustration
      *a Protective Tape

  52. REMOVE FRONT ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  53. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    B0018LD

    1. Remove the front door opening trim weatherstrip LH.

  54. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  55. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B0019J9

    1. Remove the rear door opening trim weatherstrip LH.

  56. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  57. REMOVE BACK DOOR WEATHERSTRIP

    B001894

    1. Remove the back door weatherstrip.

  58. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

    B0018QKE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the front door scuff plate outside LH.

    2. Detach the 4 clips and remove the front door scuff plate outside LH.

  59. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  60. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

    B0019EVE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the rear door scuff plate outside LH.

    2. Detach the 3 clips and remove the rear door scuff plate outside LH.

  61. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  62. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001863

    1. Detach the 6 claws of the front shoulder belt anchor plate sub-assembly LH, and slide the front shoulder belt anchor plate sub-assembly LH in the direction of the arrow to remove it.

  63. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  64. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B0019RG

    1. Detach the 6 claws and remove the rear shoulder belt anchor plate sub-assembly LH.

  65. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  66. REMOVE ROOF SIDE INNER GARNISH COVER LH

    B001A5M

    1. Detach the 7 claws and remove the roof side inner garnish cover LH.

  67. REMOVE ROOF SIDE INNER GARNISH COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  68. REMOVE REAR NO. 1 SEAT SHOULDER BELT HANGER

    Tech Tips

    Use the same procedure for both rear No. 1 seat shoulder belt hangers.


    1. B0018YME01
      Text in Illustration
      *a Spring Nut

      Remove the 2 spring nuts and rear No. 1 seat shoulder belt hanger.

  69. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER LH

    B0019DJE01
    Text in Illustration
    *a Spring Nut

    1. Remove the 2 spring nuts and rear No. 2 seat shoulder belt hanger.

  70. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedures described for the LH side.

  71. REMOVE QUARTER TRIM COVER SUB-ASSEMBLY LH

    B0019B2

    1. Remove the 8 screws and duct.

    2. B001A1I

      Remove the 7 screws.

    3. Detach the 4 claws and remove the quarter trim cover sub-assembly LH.

  72. REMOVE QUARTER TRIM COVER SUB-ASSEMBLY RH

    B0019UG

    1. Remove the 7 screws.

    2. Detach the 4 claws and remove the quarter trim cover sub-assembly RH.

  73. REMOVE NO. 2 CUP HOLDER

    B001ACT

    1. Remove the 5 screws.

    2. Detach the 3 claws and remove the No. 2 cup holder.

  74. REMOVE NO. 1 CUP HOLDER

    B0019UM

    1. Remove the 5 screws.

    2. Detach the 3 claws and remove the No. 1 cup holder.

  75. REMOVE NO. 1 SIDE TRIM BASE COVER LH

    B001AVL

    1. Detach the 4 claws and remove the No. 1 side trim base cover LH.

  76. REMOVE NO. 1 SIDE TRIM BASE COVER RH

    B0018I7

    1. Remove the 6 screws and duct.

    2. B001B01

      Detach the 4 claws and remove the No. 1 side trim base cover RH.

  77. REMOVE NO. 2 SIDE TRIM BASE COVER LH

    B001B5H

    1. Detach the 4 claws and remove the No. 2 side trim base cover LH.

  78. REMOVE NO. 2 SIDE TRIM BASE COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  79. REMOVE FOLD SEAT SWITCH ASSEMBLY

    B001AUU

    1. Detach the 6 clips and remove the fold seat switch assembly.

  80. REMOVE QUARTER TRIM COVER LH

    B001B0A

    1. Detach the 6 clips and remove the quarter trim cover LH.

  81. REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH


    1. Remove the quarter trim lid sub-assembly RH.

  82. REMOVE SIDE TRIM BOX COVER (w/o Woofer)


    1. Remove the side trim box cover.

  83. REMOVE SIDE TRIM BOX (w/o Woofer)

    B0019LF

    1. Remove the 9 screws and side trim box.