PRE-CRASH SAFETY SYSTEM, Diagnostic DTC:C1A46

DTC Code DTC Name
C1A46 Yaw Rate Sensor

DESCRIPTION

The driving support ECU assembly receives yaw rate sensor signals from the yaw rate sensor assembly and skid control ECU assembly via CAN communication. If the driving support ECU assembly receives yaw rate sensor malfunction signals from the yaw rate sensor assembly or skid control ECU assembly, DTC C1A46 is stored.

DTC Code DTC Detection Condition Trouble Area
C1A46

  • While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor malfunction signals from yaw rate sensor for approximately 10 seconds.

  • While the vehicle is being driven at a speed of 5 km/h (4 mph) or more, the driving support ECU assembly receives a yaw rate sensor zero point malfunction signals from skid control ECU assembly for approximately 10 seconds.

  • Electronically controlled brake system

  • Yaw rate sensor

  • Skid control ECU assembly

  • Driving support ECU assembly

CAUTION / NOTICE / HINT

Note


  • When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

  • The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.


PROCEDURE


  1. CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

    Tech Tips

    Pre-crash safety system DTC C1A46 may be stored due to a malfunction in the electronically controlled brake system. Therefore, it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.


    1. Check for DTCs Click here.

      Result
      Result Proceed to
      Electronically controlled brake system DTCs are not output A
      Electronically controlled brake system DTCs are output B

    B

    GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM Click here

    A

  2. CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)


    1. Clear the DTCs Click here.

    2. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.

    3. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1A46 is not output A
      DTC C1A46 is output B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

  3. REPLACE DRIVING SUPPORT ECU ASSEMBLY


    1. Replace the driving support ECU assembly Click here.


    NEXT

  4. CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)


    1. Clear the DTCs Click here.

    2. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.

    3. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1A46 is not output A
      DTC C1A46 is output B

    A

    END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

    B

  5. REPLACE YAW RATE SENSOR


    1. Replace the yaw rate sensor assembly Click here.


    NEXT

  6. CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)


    1. Clear the DTCs Click here.

    2. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Drive the vehicle at a speed of 5 km/h (4 mph) or more for 10 seconds or more.

    3. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1A46 is not output A
      DTC C1A46 is output B

    A

    END (YAW RATE SENSOR ASSEMBLY WAS DEFECTIVE)

    B

    REPLACE SKID CONTROL ECU ASSEMBLY Click here