DYNAMIC REAR STEERING SYSTEM, Diagnostic DTC:C1597/43

DTC Code DTC Name
C1597/43 Lost Communication between VGRS and DRS

DESCRIPTION

The DRS ECU (rear steering control ECU) communicates with the VGRS ECU (front steering control ECU) via the local bus.

DTC Code DTC Detection Condition Trouble Area
C1597/43

All conditions are met for approximately 3 seconds or more:


  • 1 second or more elapses after turning the power switch on (IG).

  • The power source voltage is 10 to 16 V.

  • The signal from the VGRS ECU is lost (local bus).

  • VGRS ECU (front steering control ECU)

  • DRS ECU (rear steering control ECU)

  • Harness or connector

WIRING DIAGRAM

A000SJWE13
*1 CANVGRS ECU (Front Steering Control ECU)
*2 DRS ECU (Rear Steering Control ECU)

CAUTION / NOTICE / HINT

Note


  • When replacing the VGRS ECU (front steering control ECU), perform actuator angle neutral position calibration and initialization after replacement (See page ).

    Click here

  • When replacing the DRS ECU (rear steering control ECU), perform neutral position memorization and motor rotation angle sensor calibration Click here.

PROCEDURE


  1. CHECK FOR DTC


    1. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC U0130/41 is not output A
      DTC U0130/41 is output B

    B

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    A

  2. CHECK FOR DTC (VARIABLE GEAR RATIO STEERING SYSTEM)


    1. Check for DTCs in the variable gear ratio steering system Click here.

      Result
      Result Proceed to
      DTC U0134/56 is not output A
      DTC U0134/56 is output B

    B

    GO TO VARIABLE GEAR RATIO STEERING SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (CAN+, CAN- TERMINAL)


    1. Turn the power switch off.

    2. Check the connection condition of the VGRS ECU (front steering control ECU) connector and terminals.

    3. Disconnect the VGRS ECU (front steering control ECU) connector.

    4. A000RU4E02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to VGRS ECU [Front Steering Control ECU])

      Measure the resistance according to the value(s) in the table below.

      Tech Tips

      Measure the resistance of the wire harness and DRS ECU (rear steering control ECU) at the VGRS ECU (front steering control ECU) connector.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N104-10 (CAN+) - N104-11(CAN-) Always 100 to 140 Ω
      N104-10 (CAN+) - Body ground Always 100 kΩ or higher
      N104-11 (CAN-) - Body ground Always 100 kΩ or higher

    NG

    INSPECT REAR STEERING CONTROL ECU (CAN+, CAN- TERMINAL) Click here

    OK

  4. INSPECT FRONT STEERING CONTROL ECU (CAN+, CAN- TERMINAL)


    1. Turn the power switch off.

    2. Disconnect the N104 VGRS ECU (front steering control ECU) connector.

    3. A000NX9E03
      Text in Illustration
      *a

      Component without harness connected

      (VGRS ECU [Front Steering Control ECU])

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      10 (CAN+) - 11(CAN-) Always 100 to 140 Ω
      10 (CAN+) - Body ground Always 100 kΩ or higher
      11 (CAN-) - Body ground Always 100 kΩ or higher

    NG

    REPLACE FRONT STEERING CONTROL ECU Click here

    OK

  5. RECONFIRM DTC


    1. Reconnect the N104 VGRS ECU (front steering control ECU) connector.

    2. Clear the DTCs Click here.

    3. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1597/57 is not output A
      DTC C1597/57 is output B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE FRONT STEERING CONTROL ECU Click here

  6. INSPECT REAR STEERING CONTROL ECU (CAN+, CAN- TERMINAL)


    1. Turn the power switch off.

    2. Disconnect the U42 DRS ECU (rear steering control ECU) connector.

    3. A000RNQE03
      Text in Illustration
      *a

      Component without harness connected

      (DRS ECU [Rear Steering Control ECU])

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      11 (CAN+) - 8 (CAN-) Always 100 to 140 Ω
      11 (CAN+) - Body ground Always 100 kΩ or higher
      8 (CAN-) - Body ground Always 100 kΩ or higher

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    NG

    REPLACE REAR STEERING CONTROL ECU Click here