ELECTRONICALLY CONTROLLED BRAKE SYSTEM, Diagnostic DTC:C1365

DTC Code DTC Name
C1365 Accumulator Pressure Sensor

DESCRIPTION

The accumulator pressure sensor is built into the brake actuator assembly.

The skid control ECU assembly detects the accumulator pressure from the data sent from the accumulator pressure sensor, and then runs and stops the pump motor by operating the motor relay.

DTCs may be output if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC Code INF Code DTC Detection Condition Trouble Area
C1365 211 Sensor power 1 (VCM) voltage is 4.7 V or less or 5.3 V or more for at least 0.05 seconds.

  • Brake actuator assembly (Accumulator pressure sensor)

  • Accumulator pressure sensor circuit

  • Accumulator pressure sensor power supply

  • Brake actuator assembly

  • Skid control ECU assembly
↑ 212 Accumulator pressure sensor output voltage (PAC1) is less than 0.25 V or 4.53 V or more for at least 0.05 seconds. ↑
↑ 214 While the motor is off, the total of the wheel cylinder pressure sensor values of all 4 wheels increases but the accumulator pressure changes little for 0.5 seconds or more. ↑
↑ 215 Accumulator pressure sensor output voltage (PAC1) is stuck at 4.53 V or less. ↑

WIRING DIAGRAM

Refer to DTCs C1246, C1281 and C1364 Click here.

CAUTION / NOTICE / HINT

Note

When replacing the skid control ECU assembly or brake actuator assembly, perform initialization and calibration of the linear solenoid valve Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Disconnect the A14 skid control ECU assembly connector and the A12 brake actuator assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      A14-28 (E) - A12-45 (E) Always Below 1 Ω
      A14-28 (E) - Body ground Always 10 kΩ or higher
      A14-27 (VCM) - A12-35 (VCM) Always Below 1 Ω
      A14-27 (VCM) - Body ground Always 10 kΩ or higher
      A14-26 (PAC1) - A12-46 (PAC1) Always Below 1 Ω
      A14-26 (PAC1) - Body ground Always 10 kΩ or higher
      A14-9 (PCK1) - A12-37 (PCK1) Always Below 1 Ω
      A14-9 (PCK1) -Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      A14-28 (E) - A12-14 (E) Always Below 1 Ω
      A14-28 (E) - Body ground Always 10 kΩ or higher
      A14-27 (VCM) - A12-10 (VCM) Always Below 1 Ω
      A14-27 (VCM) - Body ground Always 10 kΩ or higher
      A14-26 (PAC1) - A12-15 (PAC1) Always Below 1 Ω
      A14-26 (PAC1) - Body ground Always 10 kΩ or higher
      A14-9 (PCK1) - A12-12 (PCK1) Always Below 1 Ω
      A14-9 (PCK1) -Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. RECONFIRM DTC


    1. Reconnect the skid control ECU assembly connector and the brake actuator assembly connector.

    2. Clear the DTCs Click here.

    3. Perform a road test.

    4. Check if the same DTC is output Click here.

      Result
      Result Proceed to
      DTC (C1365) is output A
      DTC (C1365) is not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  3. CHECK FREEZE FRAME DATA


    1. Check the INF code from the Freeze Frame Data memorized when the DTC (C1365/54) is stored Click here.

      Result
      Result Proceed to
      INF code 211 is output A
      INF code 212, 214 and/or 215 is output B

    A

    REPLACE SKID CONTROL ECU ASSEMBLY Click here

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here