REAR DOOR WINDOW FRAME MOULDING INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY LH


    1. Attach the 2 claws to install the rear door window frame moulding.

    2. Install a nose piece to an air riveter or hand riveter.

    3. Insert the mandrel part of a new rivet into the nose piece.

    4. Place the riveter upright against the rear door window frame moulding and install the 8 rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • B002BI7E60

        Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

        Text in Illustration
        *1 Riveter
        *2 Mandrel
        *a INCORRECT
        *b CORRECT
      • A000O0KE39

        Confirm that the rivets are seated properly against the rear door window frame moulding.

      • Do not tilt the riveter when installing the rivet to the rear door window frame moulding.

      • Do not leave any space between the rivet head and rear door window frame moulding.

        Text in Illustration
        *1 Riveter
        *a INCORRECT
        *b CORRECT
      • A000PTLE36

        Do not leave any space between the rear door window frame moulding and rear door panel. Firmly hold together the 2 items while installing the rivet.

        Text in Illustration
        *1 Riveter
        *a INCORRECT
        *b CORRECT
      A000NUV

  2. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH

    Tech Tips

    When installing the rear door front window frame moulding, heat the rear door panel and rear door front window frame moulding using a heat light.

    Standard
    Item Temperature
    Rear Door Panel 40 to 60°C (104 to 140°F)
    Rear Door Front Window Frame Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear door panel or rear door front window frame moulding excessively.


    1. Clean the rear door panel surface.


      1. Using a heat light, heat the rear door panel surface.

      2. Remove the double-sided tape from the rear door panel surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. A000QVFE03
      Text in Illustration
      *1 Double-sided Tape
      *2 Butyl Tape

      Install a new rear door front window frame moulding.


      1. Using a heat light, heat a new rear door front window frame moulding and the rear door panel surface.

      2. Remove the peeling paper from the face of the rear door front window frame moulding.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Attach the clip and guide to install the rear door front window frame moulding.

        Tech Tips

        Press the rear door front window frame moulding firmly to install it.

  3. INSTALL REAR DOOR FRONT BELT MOULDING END COVER LH

    Tech Tips

    When installing the rear door front belt moulding end cover, heat the rear door panel and rear door front belt moulding end cover using a heat light.

    Standard
    Item Temperature
    Rear Door Panel 40 to 60°C (104 to 140°F)
    Rear Door Front Belt Moulding End Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear door panel or rear door front belt moulding end cover excessively.


    1. Clean the rear door panel surface.


      1. Using a heat light, heat the rear door panel surface.

      2. Remove the double-sided tape from the rear door panel surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. A000SAKE02
      Text in Illustration
      *1 Double-sided Tape

      Install a new rear door front belt moulding end cover.


      1. Using a heat light, heat a new rear door front belt moulding end cover and the rear door panel surface.

      2. Remove the peeling paper from the face of the rear door front belt moulding end cover.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Attach the 2 clips to install the rear door front belt moulding end cover.

        Tech Tips

        Press the rear door front belt moulding end cover firmly to install it.

  4. INSTALL REAR DOOR WEATHERSTRIP LH


    1. Install the upper part of the rear door weatherstrip.

  5. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

    Click here

  6. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  7. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

    Click here

  8. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

    Click here

  9. INSTALL REAR DOOR GLASS RUN LH

    Click here

  10. INSTALL REAR DOOR SERVICE HOLE COVER LH

    Click here

  11. INSTALL REAR NO. 2 SPEAKER ASSEMBLY

    Click here

  12. INSTALL REAR DOOR ARMREST SET BRACKET LH

    Click here

  13. INSTALL REAR DOOR FRAME GARNISH LH

    Click here

  14. INSTALL REAR SIDE CURTAIN ASSEMBLY LH (w/ Rear Sunshade)

    Click here

  15. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  16. INSTALL REAR DOOR TRIM COVER LH

    Click here

  17. INSTALL REAR DOOR NO. 1 STIFFENER CUSHION

    Click here

  18. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  19. INSTALL REAR DOOR HOLE COVER

    Click here

  20. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  21. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click here

  22. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  23. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  24. INSTALL LUGGAGE COMPARTMENT FLOOR MAT

    Click here

  25. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here