FRONT DOOR WINDOW FRAME MOULDING INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH


    1. Attach the claw and clip to install the front door outside moulding.

    2. Install a nose piece to an air riveter or hand riveter.

    3. Insert the mandrel part of a new rivet into the nose piece.

    4. Place the riveter upright against the front door outside moulding and install the 7 rivets.

      Tech Tips

      If the rivet cannot be cut, pull it once and cut it.

      Note


      • B002BI7E60

        Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

        Text in Illustration
        *1 Riveter
        *2 Mandrel
        *a INCORRECT
        *b CORRECT
      • A000O0KE39

        Confirm that the rivets are seated properly against the front door outside moulding.

      • Do not tilt the riveter when installing the rivet to the front door outside moulding.

      • Do not leave any space between the rivet head and front door outside moulding.

        Text in Illustration
        *1 Riveter
        *a INCORRECT
        *b CORRECT
      • A000PTLE36

        Do not leave any space between the front door outside moulding and front door panel. Firmly hold together the 2 items while installing the rivet.

        Text in Illustration
        *1 Riveter
        *a INCORRECT
        *b CORRECT
      A000OOK

  2. INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER LH


    1. Install the front door lower frame upper cover with the nut.

  3. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

    Tech Tips

    When installing the front door rear window frame moulding, heat the front door panel and front door rear window frame moulding using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    Front Door Rear Window Frame Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the front door panel or front door rear window frame moulding excessively.


    1. Clean the front door panel surface.


      1. Using a heat light, heat the front door panel surface.

      2. Remove the double-sided tape from the front door panel surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. A000SGJE03
      Text in Illustration
      *1 Double-sided Tape
      *2 Butyl Tape

      Install a new front door rear window frame moulding.


      1. Using a heat light, heat a new front door rear window frame moulding and the front door panel surface.

      2. Remove the peeling paper from the face of the front door rear window frame moulding.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Attach the clip and guide to install the front door rear window frame moulding.

        Tech Tips

        Press the front door rear window frame moulding firmly to install it.

  4. INSTALL FRONT DOOR REAR BELT MOULDING END COVER LH

    Tech Tips

    When installing the front door rear belt moulding end cover, heat the front door panel and front door rear belt moulding end cover using a heat light.

    Standard
    Item Temperature
    Front Door Panel 40 to 60°C (104 to 140°F)
    Front Door Rear Belt Moulding End Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the front door panel or front door rear belt moulding end cover excessively.


    1. Clean the front door panel surface.


      1. Using a heat light, heat the front door panel surface.

      2. Remove the double-sided tape from the front door panel surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. A000R8TE02
      Text in Illustration
      *1 Double-sided Tape

      Install a new front door rear belt moulding end cover.


      1. Using a heat light, heat a new front door rear belt moulding end cover and the front door panel surface.

      2. Remove the peeling paper from the face of the front door rear belt moulding end cover.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. Attach the 2 clips to install the front door rear belt moulding end cover.

        Tech Tips

        Press the front door rear belt moulding end cover firmly to install it.

  5. INSTALL FRONT DOOR WEATHERSTRIP LH


    1. Install the upper part of the front door weatherstrip.

  6. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

    Click here

  7. INSTALL FRONT DOOR GLASS RUN LH

    Click here

  8. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

    Click here

  9. INSTALL FRONT DOOR SERVICE HOLE COVER LH

    Click here

  10. INSTALL FRONT DOOR ARMREST SET BRACKET LH

    Click here

  11. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

    Click here

  12. INSTALL DOOR FRAME GARNISH LH

    Click here

  13. INSTALL FRONT DOOR TRIM COVER LH

    Click here

  14. INSTALL FRONT DOOR NO. 1 STIFFENER CUSHION

    Click here

  15. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  16. INSTALL FRONT DOOR HOLE COVER

    Click here

  17. INSTALL COURTESY LIGHT ASSEMBLY

    Click here

  18. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  19. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

    Click here

  20. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  21. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  22. INSTALL LUGGAGE COMPARTMENT FLOOR MAT

    Click here

  23. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  24. CHECK POWER SEAT CONTROL SYSTEM


    1. for LHD:

      Click here

    2. for RHD:

      Click here