SLIDING ROOF HOUSING INSTALLATION

PROCEDURE


  1. INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY


    1. Temporarily install the sliding roof housing sub-assembly with the 4 bolts (vehicle body side) and 8 nuts.

    2. Tighten the 8 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    3. Tighten the 4 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      B001H1U

    4. Connect the 4 drain hoses.

  2. INSTALL SLIDING ROOF WEATHERSTRIP


    1. Install the sliding roof weatherstrip as follows:


      1. Position the joint of the sliding roof weatherstrip at the rear center.

      2. Align the alignment mark on the sliding roof weatherstrip with the middle marks at the corners of the sliding roof glass sub-assembly and install the sliding roof weatherstrip.

      3. Install the lip of the sliding roof weatherstrip firmly.

        B001IFQE02
        Text in Illustration
        *a Correct *b Incorrect
        *c Joint *d Vehicle Rear
        *e Alignment Mark *f Middle Mark

  3. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY


    1. B001GN1

      Using a T25 "TORX" driver, temporarily install the sliding roof glass sub-assembly with the 4 screws.

    2. Perform a level check.


      1. Check the difference in the level between the roof panel and upper surface of the weatherstrip labeled "a" when the sliding roof glass is fully closed.

        B001FNPE02
        Text in Illustration
        *a Even - -
        Standard
        Area Specified Condition
        A - A -2.0 to 1.0 mm (-0.0787 to 0.0394 in.)
        B - B -1.0 to 2.0 mm (-0.0394 to 0.0787 in.)
        C - C -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
        D - D -1.0 to 1.5 mm (-0.0394 to 0.0591 in.)

        Tech Tips

        "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

      2. Perform a gap check.

        Check the gap between the roof panel and roof glass.

        Note

        The gap must be even all around.

    3. B001EWP

      Using a T25 "TORX" driver, tighten the 4 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  4. CHECK FOR WATER LEAK


    1. After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.

      If there are any leaks, readjust the sliding roof glass sub-assembly.

  5. INSTALL SLIDING ROOF SIDE GARNISH LH

    B001CBE

    1. Attach the 5 claws to install the sliding roof side garnish LH.

  6. INSTALL SLIDING ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL TELEVISION DISPLAY BRACKET A (w/ Rear Seat Entertainment System)


    1. B001HWT

      Install the television display bracket A with the 4 nuts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }
      Text in Illustration
      B001DEF Front Side

  8. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)

    Click here

  9. INSTALL REAR NO. 3 ROOF AIR DUCT (for Dual Air Conditioning System)

    Click here

  10. INSTALL REAR NO. 5 ROOF AIR DUCT (for Dual Air Conditioning System)

    Click here

  11. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

    Click here

  12. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL ROOF HEADLINING ASSEMBLY (for 3 Door)

    Click here

  14. INSTALL ROOF HEADLINING ASSEMBLY (for 5 Door)

    Click here

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. CHECK SRS WARNING LIGHT

    Click here