ROOF HEADLINING(for 5 Door) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart.

    Click here

PROCEDURE


  1. INSTALL REAR NO. 3 SIDE RAIL SPACER LH


    1. Attach the 2 claws to install the rear No. 3 side rail spacer LH.

  2. INSTALL REAR NO. 3 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. Attach the 2 claws to install the rear No. 2 side rail spacer LH.

  4. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. Attach the 2 claws to install the rear side rail spacer LH.

  6. INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL DECK SIDE TRIM COVER LH


    1. Attach the 3 claws and 2 guides to install the deck side trim cover LH.

  8. INSTALL QUARTER TRIM JACK COVER


    1. Attach the 3 claws and 2 guides to install the quarter trim jack cover.

  9. INSTALL QUARTER TRIM COVER

    Tech Tips

    Use the same procedure for the other quarter trim cover.


    1. Attach the 2 claws to install the quarter trim cover.

  10. INSTALL REAR SEAT SHOULDER BELT HANGER LH


    1. Attach the claw and guide to install the rear seat shoulder belt hanger LH.

  11. INSTALL REAR SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. INSTALL ROOF SIDE INNER GARNISH CAP LH (w/o Rear No. 2 Seat)


    1. Attach the 4 claws and 2 guides to install the roof side inner garnish cap LH.

  13. INSTALL ROOF SIDE INNER GARNISH CAP RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  14. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. Attach the 6 claws to install the rear belt anchor plate sub-assembly LH.

  15. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. Attach the 5 claws to install the front belt anchor plate sub-assembly LH.

  17. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. INSTALL ROOF HEADLINING ASSEMBLY


    1. Place the roof headlining into the vehicle through the back door.

      Note

      Be careful not to damage the roof headlining when placing it in the cabin.

    2. B001D5P

      w/o Sliding Roof:


      1. Attach the 2 clips to install the roof headlining assembly.

    3. B001IL6C03
      *a Guide
      *b Fastener

      w/ Sliding Roof:


      1. Attach the 2 clips, 2 guides and 8 fasteners to install the roof headlining assembly.

    4. B001EY4C02
      *a Guide
      *b Fastener

      w/ Rear Seat Entertainment System:


      1. Attach the 2 clips, 2 guides and 6 fasteners to install the roof headlining assembly.

    5. w/ Rear Seat Entertainment System:


      1. Connect the 2 connectors.

    6. Connect the connector and attach the 3 clamps to the rear pillar RH.

    7. Connect the 2 connectors and attach the clamp to the rear pillar LH.

    8. Connect the 2 connectors and attach the 3 clamps to the front pillar RH.

    9. Install the bolt.

    10. Connect the 2 connectors and attach the 3 clamps to the front pillar LH.

    11. w/ Digital Audio Broadcasting Antenna:


      1. Connect the connector and attach the wire harness clamp.

    12. w/ Pre-crash Safety System:


      1. Attach the hook to install the camera earth with the bolt.

    13. w/ Sliding Roof


      1. Connect the drive gear connector.

    14. B001CS9

      w/ Rain Sensor:


      1. Connect the rain sensor connector.

    15. B001DOL

      w/ EC Mirror:


      1. Connect the inner mirror connector.

    16. B001HWHC04
      *A w/ Camera Heater

      w/ Pre-crash Safety System:


      1. Connect the 2 connectors.

    17. w/ Pre-crash Safety System, w/ Camera Heater:


      1. Connect the 3 connectors.

  19. INSTALL VISOR HOLDER

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Attach the 2 claws.

    2. Push in the visor holder to install it.

  20. INSTALL VISOR ASSEMBLY LH


    1. Install the visor assembly LH with the 2 screws.

  21. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. INSTALL VISOR BRACKET COVER LH

    Tech Tips

    Use the same procedure for the other visor bracket cover.


    1. Attach the 4 claws to install the visor bracket cover LH.

  23. INSTALL VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. INSTALL REAR HEADER SPEAKER ASSEMBLY (w/ Rear Air Conditioning System)

    Click here

  25. INSTALL REAR SIDE NO. 1 AIR DUCT (w/ Rear Air Conditioning System)

    Click here

  26. INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH

    B001IKLC03
    *a New Clip

    1. Install 3 new clips to the No. 1 roof side rail garnish LH.

    2. Attach the 3 clips to install the No. 1 roof side rail garnish LH.

  27. INSTALL NO. 1 ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)

    Click here

  29. INSTALL NO. 2 ROOM LIGHT ASSEMBLY

    Click here

  30. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    Click here

  31. INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  32. INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  33. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  34. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  35. INSTALL MAP LIGHT ASSEMBLY

    Click here

  36. INSTALL ASSIST GRIP (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Install the assist grip with the 2 bolts.

    2. Attach the 4 claws to close the 2 covers.

  37. INSTALL REAR ASSIST GRIP ASSEMBLY LH

    B001FQ7

    1. Assemble the rear assist grip assembly LH, 2 clips and 2 covers as shown in the illustration.

    2. Install the rear assist grip sub-assembly LH.

  38. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. INSTALL ASSIST GRIP SUB-ASSEMBLY

    B001DNR

    1. Assemble the assist grip sub-assembly, 2 clips and 2 covers as shown in the illustration.

    2. Install the assist grip sub-assembly.

  40. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH


    1. w/o Rear No. 2 Seat:


      1. Attach the 7 clips and 2 guides to install the rear quarter trim panel assembly LH.

    2. w/ Rear No. 2 Seat:


      1. Attach the 4 clips and 2 guides and pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel.

      2. Attach the 7 clips and 2 guides to install the rear quarter trim panel assembly LH.

  41. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  42. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH


    1. Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel assembly LH.

    2. Attach the 2 clips and 2 guides to install the front quarter trim panel assembly LH.

  43. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  44. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. w/o Rear No. 2 Seat, w/o Rear Air Conditioning System:


      1. Pass the rear seatback lock control lever base through the deck trim side panel assembly LH.

      2. Attach the 5 clips and 8 claws to install the deck trim side panel assembly LH.

      3. Install the 4 bolts and 2 screws.

      4. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly LH.

      5. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. w/o Rear No. 2 Seat, w/ Rear Air Conditioning System:


      1. Attach the 5 clips and 8 claws to install the deck trim side panel assembly LH.

      2. Install the 2 bolts and 2 screws.

      3. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. w/ Rear No. 2 Seat:


      1. Attach the 4 clips and 8 claws to install the deck trim side panel assembly LH.

      2. Install the 2 bolts and 2 screws.

      3. Install the rear No. 2 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      4. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
  45. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. w/o Rear No. 2 Seat, w/o Rear Air Conditioning System:


      1. Connect each connector.

      2. Pass the rear seatback lock control lever base through the deck trim side panel assembly RH.

      3. Attach the 5 clips and 8 claws to install the deck trim side panel assembly RH.

      4. Install the 4 bolts and screw.

      5. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly RH.

      6. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. w/o Rear No. 2 Seat, w/ Rear Air Conditioning System:


      1. Connect each connector.

      2. Attach the 4 clips and 8 claws to install the deck trim side panel assembly RH.

      3. Install the 2 bolts and screw.

      4. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. w/ Rear No. 2 Seat:


      1. Connect each connector.

      2. Attach the 4 clips and 8 claws to install the deck trim side panel assembly RH.

      3. Install the 2 bolts and screw.

      4. Install the rear No. 2 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      5. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
  46. INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Install the assist grip sub-assembly with the 2 bolts.

  47. INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for all assist grip plugs.


    1. Attach the 2 claws to install the assist grip plug.

  48. INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Attach the 2 claws to install the front deck side trim cover.

  49. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    Tech Tips

    Use the same procedure for the other No. 1 tonneau cover holder cap.


    1. Attach the 2 claws to install the No. 1 tonneau cover holder cap.

  50. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Install the No. 1 luggage compartment trim hook by turning it clockwise.

  51. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    Tech Tips

    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


    1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.

  52. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)


    1. Attach the 4 claws to install the rear floor carpet assembly.

      B001GZGC02
      *A w/o Deck Rail *B w/ Deck Rail
      *C for Face to Face Seat Type *D w/ Rear Air Conditioning System
  53. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)


    1. Install the floor side rail LH with the 3 bolts.

  54. INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  55. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)


    1. Attach the 5 clips and 4 claws to install the rear floor mat rear support plate.

  56. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)


    1. w/ Rear Air Conditioning System:


      1. Attach the clip to install the No. 1 deck board sub-assembly.

    2. w/o Rear Air Conditioning System:


      1. Attach the clip to install the No. 1 deck board sub-assembly.

  57. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

    B001CA7C04
    *1 Luggage Hold Belt Striker

    Tech Tips

    Use the same procedure for the other front luggage compartment trim cover.


    1. Install the luggage hold belt striker and front luggage compartment trim cover with the bolt.

    2. Attach the 4 claws to install the cap.

  58. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  59. INSTALL CENTER PILLAR GARNISH LH


    1. Pass the front seat outer belt floor anchor through the center pillar garnish LH.

    2. Attach the 2 clips and 2 guides to install the center pillar garnish LH.

    3. Install the bolt.

  60. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  61. INSTALL NO. 2 ASSIST GRIP

    Tech Tips

    Use the same procedure for the other No. 2 assist grip.


    1. Attach the 2 claws to install the No. 2 assist grip.

    2. Install the 2 bolts.

  62. INSTALL NO. 2 ASSIST GRIP PLUG LH

    Tech Tips

    Use the same procedure for the other front No. 2 assist grip plug.


    1. Attach the 2 claws to install the front No. 2 assist grip plug.

  63. INSTALL NO. 2 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  64. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. Attach the 4 claws and 2 clips to install the lower center pillar garnish LH.

    2. Install the front seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
  65. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  66. INSTALL OUTER LAP BELT ANCHOR COVER

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.


    1. Attach the 3 claws to install the outer lap belt anchor cover.

  67. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B001FFPC03
    *a Paint Mark
    *b Mark Position

    1. Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle and install the rear door opening trim weatherstrip LH as shown in the illustration.

  68. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  69. INSTALL REAR DOOR SCUFF PLATE LH


    1. Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate LH.

  70. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  71. INSTALL INSIDE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)


    1. Install the quarter scuff plate LH with the 2 bolts.

  72. INSTALL INSIDE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  73. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for all rear No. 1 floor step covers.


    1. Attach the 2 claws to install the rear No. 1 floor step cover.

  74. INSTALL FRONT PILLAR GARNISH LH


    1. Attach the 3 guides to install the front pillar garnish LH.

  75. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  76. INSTALL NO. 1 ASSIST GRIP

    Tech Tips

    Use the same procedure for the other No. 1 assist grip.


    1. Attach the 2 claws to install the No. 1 assist grip.

    2. Install the 2 bolts.

  77. INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH

    Tech Tips

    Use the same procedure for the other front No. 1 assist grip plug.


    1. Attach the 2 claws to install the front No. 1 assist grip plug LH.

  78. INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  79. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. B001EU7C03
      *a Paint Mark
      *b Mark Position

      Align the paint mark on the front door opening trim weatherstrip LH with the mark position on the vehicle and install the front door opening trim weatherstrip LH as shown in the illustration.

  80. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  81. INSTALL COWL SIDE TRIM BOARD LH


    1. B001C83N01

      Attach the clip and claw to install the cowl side trim board LH.

      Tech Tips

      Attach the clip and claw in the order shown in the illustration.

    2. Install the clip.

  82. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  83. INSTALL DOOR SCUFF PLATE ASSEMBLY LH


    1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly LH.

  84. INSTALL DOOR SCUFF PLATE ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  85. INSTALL REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)


    1. for 60/40 Split Double-folding Seat Type LH Side:

      Click here

    2. for 60/40 Split Double-folding Seat Type RH Side:

      Click here

  86. INSTALL REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. for 60/40 Split Slide Walk-in Seat Type LH Side:

      Click here

    2. for 60/40 Split Slide Walk-in Seat Type RH Side:

      Click here

  87. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. for Manual Seat Type:

      Click here

    2. for Power Seat Type:

      Click here

    3. for Face to Face Seat Type:

      Click here

  88. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here