ROOF HEADLINING(for 3 Door) INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL DECK SIDE TRIM COVER RH (w/o Spare Tire)

   
   

   1. Attach the 7 claws and 3 guides to install the deck side trim cover RH.

   2. Turn the 2 knobs to engage the lock.

2. INSTALL QUARTER TRIM JACK COVER (w/ Spare Tire)

   
   

   1. Attach the 7 claws and 3 guides to install the quarter trim jack cover.

3. INSTALL QUARTER TRIM COVER

   Tech Tips

   Use the same procedure for the other quarter trim cover.

   
   

   1. Attach the 2 claws to install the quarter trim cover.

4. INSTALL REAR SEAT SHOULDER BELT HANGER LH

   Tech Tips

   Use the same procedure for the other rear seat shoulder belt hanger.

   
   

   1. Attach the claw and guide to install the rear seat shoulder belt hanger LH.

5. INSTALL REAR SEAT SHOULDER BELT HANGER RH

   Tech Tips

   Use the same procedure described for the LH side.

6. INSTALL DECK SIDE TRIM CUP HOLDER LH

   
   

   1. Attach the 4 claws to install the deck side trim cup holder LH.

7. INSTALL DECK SIDE TRIM CUP HOLDER RH

   Tech Tips

   Use the same procedure described for the LH side.

8. INSTALL REAR NO. 2 SIDE RAIL SPACER LH

   
   

   1. Attach the 4 claws to install the rear No. 2 side rail spacer LH.

   2. Install the clip.

9. INSTALL REAR NO. 2 SIDE RAIL SPACER RH

   Tech Tips

   Use the same procedure described for the LH side.

10. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    
    

    1. Attach the 4 claws to install the front shoulder belt anchor plate sub-assembly LH.

11. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

12. INSTALL ROOF HEADLINING ASSEMBLY

    
    

    1. Place the roof headlining assembly into the vehicle through the back door.

       Note

       Be careful not to damage the roof headlining assembly when placing it in the cabin.

    2. 

       w/o Sliding Roof:

       
       

       1. Attach the 2 clips to install the roof headlining assembly.

    3. 

       *a	Guide
       *b	Fastener

       w/ Sliding Roof:

       
       

       1. Attach the 2 clips, 2 guides and 8 fasteners to install the roof headlining.

    4. Connect the connector and attach the 4 clamps to the rear pillar RH.

    5. Connect the connector and attach the 3 clamps to the rear pillar LH.

    6. Connect the 2 connectors and attach the 3 clamps to the front pillar RH.

    7. Install the bolt.

    8. Connect the 2 connectors and attach the 3 clamps to the front pillar LH.

    9. w/ Digital Audio Broadcasting Antenna:

       
       

       1. Connect the connector and attach the wire harness clamp.

    10. w/ Pre-crash Safety System:

        
        

        1. Attach the hook to install the camera earth with the bolt.

    11. w/ Sliding Roof

        
        

        1. Connect the drive gear connector.

    12. 

        w/ Rain Sensor:

        
        

        1. Connect the rain sensor connector.

    13. 

        w/ EC Mirror:

        
        

        1. Connect the inner mirror connector.

    14. 

        *A	w/ Camera Heater

        w/ Pre-crash Safety System:

        
        

        1. Connect the 3 connectors.

    15. w/ Pre-crash Safety System, w/ Camera Heater:

        
        

        1. Connect the 3 connectors.

13. INSTALL VISOR HOLDER

    Click here

14. INSTALL VISOR ASSEMBLY LH

    Click here

15. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

16. INSTALL VISOR BRACKET COVER LH

    Click here

17. INSTALL VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

18. INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH

    
    
    1. 

       *a

       New Clip

       Install 5 new clips to the No. 1 roof side rail garnish LH.

    2. Attach the 5 clips to install the No. 1 roof side rail garnish LH.

19. INSTALL NO. 1 ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

20. INSTALL NO. 2 ROOM LIGHT ASSEMBLY

    Click here

21. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    Click here

22. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

23. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

24. INSTALL MAP LIGHT ASSEMBLY

    Click here

25. INSTALL REAR ASSIST GRIP ASSEMBLY LH

    Click here

26. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

27. INSTALL ASSIST GRIP SUB-ASSEMBLY

    Click here

28. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH

    
    

    1. Attach the 4 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear quarter trim panel assembly LH.

    2. Attach the 7 clips to install the rear quarter trim panel assembly LH.

29. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

30. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

    
    

    1. Pass the front seat outer belt floor anchor through the front quarter trim panel assembly LH.

    2. Attach the 2 clips and 2 guides to install the front quarter trim panel assembly LH.

    3. Install the bolt.

31. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

32. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

    
    

    1. Attach the 9 claws and 12 clips to install the deck trim side panel assembly LH.

    2. Install the 3 bolts and 2 screws.

    3. Install the rear No. 1 seat outer belt floor anchor with the bolt.

       Torque:

       42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    4. Install the front seat outer belt floor anchor with the bolt.

       Torque:

       42 N*m  { 428 kgf*cm, 31 ft.*lbf }

33. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

    
    

    1. Connect the connector.

    2. Attach the 9 claws and 12 clips to install the deck trim side panel assembly RH.

    3. Install the 3 bolts and 2 screws.

    4. Install the rear No. 1 seat outer belt floor anchor with the bolt.

       Torque:

       42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    5. Install the front seat outer belt floor anchor with the bolt.

       Torque:

       42 N*m  { 428 kgf*cm, 31 ft.*lbf }

34. INSTALL OUTER LAP BELT ANCHOR COVER

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.

    
    

    1. Attach the 3 claws to install the outer lap belt anchor cover.

35. INSTALL QUARTER TRIM POCKET TRAY

    
    

    1. Attach the 6 claws and 2 guides to install the quarter trim pocket tray.

36. INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    Tech Tips

    Use the same procedure for the other front deck side trim cover.

    
    

    1. Attach the 2 claws to install the front deck side trim cover.

37. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    Tech Tips

    Use the same procedure for the other tonneau cover holder cap.

    
    

    1. Attach the 2 claws to install the tonneau cover holder cap.

38. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.

    
    

    1. Install the No. 1 luggage compartment trim hook so that it is positioned horizontally.

39. INSTALL REAR FLOOR CARPET ASSEMBLY

    
    

    1. Install the rear floor carpet assembly.

40. INSTALL QUARTER TRIM COVER HOLE LH

    
    

    1. Attach the 2 claws and 2 guides to install the quarter trim cover hole LH.

41. INSTALL QUARTER TRIM COVER HOLE RH

    Tech Tips

    Use the same procedure described for the LH side.

42. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    
    

    1. Attach the 6 claws to install the rear floor mat rear support plate.

    2. Install the 5 screws.

43. INSTALL MAT SET PLATE COVER

    Tech Tips

    Use the same procedure for all mat set plate covers.

    
    

    1. Attach the 2 claws to install the mat set plate cover.

44. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    
    

    1. Install the tonneau cover assembly.

45. INSTALL FRONT PILLAR GARNISH LH

    Click here

46. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

47. INSTALL NO. 1 ASSIST GRIP

    Click here

48. INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH

    Click here

49. INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

50. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

51. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

52. INSTALL COWL SIDE TRIM BOARD LH

    Click here

53. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

54. INSTALL DOOR SCUFF PLATE ASSEMBLY LH

    Click here

55. INSTALL DOOR SCUFF PLATE ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

56. INSTALL REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)

    
    

    1. for LH Side:

       Click here

    2. for RH Side:

       Click here

57. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here